Henny Penny Evolution Elite EEG-16 Series

Questions and Answers

U
ucookSep 16, 2025
Why is my Henny Penny Evolution Elite EEG-16 Fryer oil foaming or boiling over?
- U
  uowensSep 16, 2025
  Oil foaming or boiling over in your Henny Penny fryer can be due to water in the oil. In this case, you should drain and clean the oil. It can also happen if you are using improper or bad oil, so make sure to use the recommended oil.
J
James GuzmanAug 25, 2025
What to do if my Henny Penny Evolution Elite EEG-16 Fryer is under-filled?
- K
  Kelly BaileyAug 25, 2025
  If the vat in your Henny Penny Fryer is under-filled, it could be due to several reasons: - The JIB might be low or empty, so you should fill the JIB. - The JIB oil line might be clogged or collapsed, so check the JIB line. - The filter pan might need cleaning, so clean the filter pan and change the paper or pad.
S
Susan FrancisAug 25, 2025
What to do if Henny Penny Fryer displays error code E-10?
- W
  wilkinsjacksonAug 26, 2025
  If your Henny Penny Fryer displays the error code “E-10”, it indicates a high limit issue. Allow the unit to cool down for about 15-20 minutes. Then, push up on the metal reset button located under the right side of the controls. If the high limit still doesn’t reset, the high limit component needs to be replaced.
D
Darrell LopezAug 27, 2025
What to do if Henny Penny Evolution Elite EEG-16 displays error E-20-B?
- E
  evelynwoodAug 27, 2025
  If your Henny Penny Fryer displays error code “E-20-B”, it could be due to a pressure switch failure or a loose hose, or it could be a draft fan failure or low voltage. Press the power button to turn the vat off and then back on again. If the error persists, have the pressure switch checked to ensure it is an open circuit when there is no air pressure, and make sure the hose is connected to the fan and pressure switch. Also, have the draft fan checked for low voltage.
L
Laura TerrySep 18, 2025
Why is my Henny Penny Evolution Elite EEG-16 completely inoperative?
- C
  Cameron SmithSep 18, 2025
  If your Henny Penny fryer is completely inoperative even with the power switch ON, it could be due to an open circuit. Ensure the fryer is properly plugged in and check the breaker or fuse at the supply box.
J
joel12Sep 23, 2025
What to do if Henny Penny Evolution Elite EEG-16 Fryer displays error E-93-1?
- C
  corey46Sep 23, 2025
  If your Henny Penny Fryer displays error code “E-93-1”, and the AutoLift feature is not operating, have each of the Auto-lift motors checked.
N
Norma SweeneySep 8, 2025
What to do if Henny Penny Fryer displays error E-82-D?
- A
  Adam LawrenceSep 8, 2025
  If your Henny Penny Fryer displays error code “E-82–D”, it means the selector valve has failed, indicating no activity is detected. Check the motor encoder, selector valve motor, and AIF board.
L
lpattersonSep 9, 2025
What to do if Henny Penny Evolution Elite EEG-16 displays error E-83-A?
- R
  randalllopezSep 9, 2025
  If your Henny Penny Fryer displays error code “E-83-A”, it indicates that the pressure is too high. Check the filter system in Vat #1.
A
Alexis ClarkSep 3, 2025
What to do if Henny Penny Evolution Elite EEG-16 displays error E-41 or E-46?
- H
  harrisjulianSep 3, 2025
  If your Henny Penny Fryer displays error code “E-41” or “E-46”, it indicates a programming failure. Turn the power switch to vat off, then back to on. If the display continues to show an error code, have the controls re-initialized. If the error code persists, have the control board replaced.
S
Sean WalkerSep 1, 2025
What to do if Henny Penny Evolution Elite EEG-16 displays error E-15?
- H
  Heather HarrisonSep 1, 2025
  If your Henny Penny Fryer displays error code “E-15”, ensure that the drain knob is completely pushed in. If the error persists, have the drain switch checked.