What to do if Henny Penny Fryer displays error E-83-J?
If your Henny Penny Fryer displays error code “E-83-J”, it indicates that the Bulk JIB FILL switch is on when the pressure is too high. Check the JIB fill valves.
What to do if my Henny Penny EVOLUTION ELITE EEG-244 Fryer filter motor will not run?
If the filter motor on your Henny Penny Fryer won’t run, the thermal reset button on the rear of the pump motor may be tripped. First, turn the unit’s power switch to the OFF position to prevent burns from splashing shortening. Allow the motor to cool down. Then, using a screwdriver, press hard against the button until you hear a click.
What to do if my Henny Penny EVOLUTION ELITE EEG-244 is under-filled?
If the vat in your Henny Penny Fryer is under-filled, it could be due to several reasons: - The JIB might be low or empty, so you should fill the JIB. - The JIB oil line might be clogged or collapsed, so check the JIB line. - The filter pan might need cleaning, so clean the filter pan and change the paper or pad.
What to do if Henny Penny EVOLUTION ELITE EEG-244 Fryer power switch is ON but the fryer is completely inoperative?
If your Henny Penny Fryer's power switch is ON but the fryer isn't working, it could be due to an open circuit. First, ensure the fryer is properly plugged in. If it is, check the breaker or fuse at the supply box.
What to do if Henny Penny Fryer displays error E-83-R?
If your Henny Penny Fryer displays error code “E-83-R”, it indicates that the Bulk Dispose switch is on when the pressure is too high. Check the Bulk Dispose quick-disconnect behind the fryer.
What to do if Henny Penny Fryer displays error E-93-1?
If your Henny Penny Fryer displays error code “E-93-1”, and the AutoLift feature is not operating, have each of the Auto-lift motors checked.
What to do if Henny Penny EVOLUTION ELITE EEG-244 displays error E-60?
If your Henny Penny Fryer displays error code “E-60”, it means the AIF PC board is not communicating with the PC board. Turn the power switch to off, wait 15 seconds, and then turn it back on. If the error persists, have the connector between the PC boards checked. If necessary, replace the AIF PC board or the control PC board.
What to do if Henny Penny Fryer displays error E-70C?
If your Henny Penny Fryer displays error code “E-70C”, it indicates that the drain valve jumper wire is missing or disconnected. Have the jumper wire checked on the PC board at the drain switch interlock position.
What to do if Henny Penny EVOLUTION ELITE EEG-244 Fryer displays error E-15?
If your Henny Penny Fryer displays error code “E-15”, ensure that the drain knob is completely pushed in. If the error persists, have the drain switch checked.
What to do if Henny Penny Fryer displays error E-6A?
If your Henny Penny Fryer displays error code “E-6A”, it indicates that the temperature probe is open. Turn the switch to the off position, then turn it back to on. If the display continues to show “E-6A”, the temperature probe should be checked.
Explains safety alert symbols and hazard definitions for safe operation.
Details gas supply requirements, connections, and safety precautions for natural and propane gas.
Provides instructions for performing a gas leak test after installation.
Outlines the electrical specifications and grounding requirements for safe operation.
Identifies and describes the function of various control panel buttons and fryer components.
Details procedures for filling the fryer vat with oil, including safety warnings.
Outlines the steps for starting the fryer at the beginning of the day, including Melt Cycle.
Explains the standard cooking process, including using timer buttons and handling completed cycles.
Explains how to perform a manual oil filtering procedure using the pull handle.
Details how to run an automatic oil filtering procedure using push-button controls.
Details manual oil disposal using a specific shuttle accessory.
Guides through the manual cleaning process for the fryer vat.
Details the smart touch clean-out procedure for the fryer vat.
Covers programming features like product names, cook times, temperatures, and filter settings.
Provides a guide to diagnose and resolve common operational problems and error codes.
Lists specific error codes, their causes, and recommended correction procedures.
General| Manufacturer | Henny Penny |
|---|---|
| Model | EVOLUTION ELITE EEG-244 |
| Fryer Type | Electric |
| Voltage | 208-240 V |
| Phase | 3 |
| Type | Fryer |
To Next Page
