Need help?Do you have a question about the HIKVISION DS-7616NI-I2/16P and is the answer not in the manual?
General| Operating temperature (T-T) | -10 - 55 °C |
|---|---|
| Operating relative humidity (H-H) | 10 - 90 % |
| Networking standards | IEEE 802.3af, IEEE 802.3at |
| USB 2.0 ports quantity | 1 |
| Ethernet LAN data rates | 10, 100, 1000 Mbit/s |
| Power over Ethernet (PoE) | Yes |
| Supported network protocols | TCP/IP, DHCP, IPv4, IPv6, DNS, DDNS, NTP, RTSP, SADP, SMTP, SNMP, NFS, iSCSI, ISUP, UPnP, HTTP, HTTPS |
| Power over Ethernet (PoE) ports quantity | 16 |
| AC input voltage | 100 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (typical) | 15 W |
| Total Power over Ethernet (PoE) budget | 200 W |
| Input bandwidth | 160 Mbit/s |
| Number of users | 128 user(s) |
| Output bandwidth | 256 Mbit/s |
| Maximum frame rate | 30 fps |
| Maximum resolution | 3840 x 2160 pixels |
| Alarm input channels | 4 |
| Video input channels | 16 channels |
| Supported resolutions | 3840 x 2160, 2560 x 1440, 1920 x 1080, 1600 x 1200, 1280 x 1024, 1280 x 720, 1024 x 768, 704 x 576, 704 x 480 |
| Video formats supported | H.264, H.264+, H.265, H.265+, MPEG4 |
| Analog signal format system | NTSC, PAL |
| HDD capacity | 0 GB |
| HDD interface | SATA |
| Maximum storage capacity | 8 TB |
| Number of HDDs installed | 0 |
| Number of HDDs supported | 2 |
| Product color | Black, Silver |
| Rack capacity | 1U |
| Wi-Fi | No |
Weight and Dimensions| Depth | 315 mm |
|---|---|
| Width | 385 mm |
| Height | 52 mm |
| Weight | 3000 g |
Covers the procedures for powering on, shutting down, and activating the NVR by setting an admin password.
Details the proper startup and shutdown sequences to ensure the longevity of the NVR.
Guides the user through the initial device activation process, including setting an admin password and exporting a GUID file.
Provides instructions on how to reset the admin password using the exported GUID file.
Explains the process of adding detected online IP cameras to the NVR's connection list for live view and recording.
Details how to activate IP cameras, ensuring they are in an active status before adding them to the NVR.
Explains the process of adding detected online IP cameras to the NVR's connection list for live view and recording.
Details various operations available in live view mode, such as single screen, multi-screen, auto-switch, and output modes.
Guides on setting PTZ parameters like baud rate, stop bit, and parity before controlling PTZ cameras.
Explains how to set and customize PTZ presets, patrols, and patterns for camera movement and positioning.
Details the procedure for setting specific preset locations for PTZ cameras to point to during events.
Covers setting parameters that affect image quality, such as stream type, resolution, and video encoding.
Guides on setting schedules for automatic recording and capture based on time or events.
Details how to set up motion detection parameters, including detection area, sensitivity, and trigger actions.
Explains how to configure recording or capture triggered by external alarm inputs.
Covers configuring recording triggered by Video Content Analysis (VCA) events like face detection or line crossing.
Covers various methods for playing back recorded video files, including instant, normal, event, and smart searches.
Guides on playing back video files by searching through channels, dates, and times.
Details how to play back video files recorded in a specified time duration with multi-channel simultaneous playback.
Explains how to use smart playback to search video containing motion, line crossing, or intrusion detection and play it efficiently.
Guides on playing back record files searched by event type, such as alarm input, motion detection, or VCA.
Covers methods for backing up record files using quick export, normal search, or event search.
Guides on quickly exporting record files to backup devices like USB drives or HDDs.
Explains how to back up record files and pictures by searching for specific video or picture content.
Details how to back up event-related record files by searching for specific event types like alarms or motion.
Explains how to set up an N+1 hot spare system for enhanced data reliability and automatic failover.
Details the steps to set the NVR's work mode to Hot Spare Mode for automatic failover.
Guides on configuring working devices, including their IP address and password, to link with the hot spare device.
Explains how to add working devices to the hot spare system to ensure continuous operation.
Guides on configuring motion detection parameters, including detection area, sensitivity, and alarm response actions.
Explains how to handle external sensor alarms by setting alarm inputs, types, and linkage actions.
Covers detecting video loss for a channel and configuring alarm response actions and arming schedules.
Details how to detect video tampering (lens covered) and configure alarm response actions and schedules.
Explains how to configure handling actions for various system exceptions like HDD Full, Network Disconnected, or IP Conflict.
Covers configuring various alarm response actions, including Event Hint Display, Full Screen Monitoring, Audible Warning, and Email Linkage.
Explains how to configure face detection for surveillance scenes and set actions when an alarm is triggered.
Guides on configuring vehicle detection for road traffic monitoring, including license plate capture and alarm signaling.
Details how to detect people, vehicles, or objects crossing a virtual line and configure alarm response actions.
Explains how to configure intrusion detection for people or objects entering a predefined virtual region and setting alarm triggers.
Guides on configuring region entrance detection for people, vehicles, or objects entering a predefined virtual region.
Guides on searching for detected face pictures and playing related video files based on specified conditions.
Explains how to search for suspicious behavior based on VCA detection and configure linkage methods.
Details how to search for matched vehicle plate pictures and related information using conditions like country and plate number.
Covers calculating the number of people entering or leaving an area and generating reports for analysis.
Details how to configure general network settings like working mode, NIC type, IP address, and DNS server.
Explains how to enable and configure Hik-Connect for mobile and web access to manage the NVR remotely.
Explains RAID technology and how to configure disk arrays on the NVR for data redundancy.
Guides on enabling the RAID function either during device startup wizard or in the HDD Management interface.
Details the quick disk array creation process using the one-touch configuration feature, defaulting to RAID 5.
Explains how to manually create arrays for RAID 0, 1, 5, 6, and 10, selecting physical disks and RAID levels.
Covers understanding array status (Functional, Degraded, Offline) and restoring degraded virtual disks through array rebuilding.
Describes how the NVR automatically rebuilds the array using a hot spare disk when the virtual disk is in a degraded status.
Explains how to manually rebuild the array to restore it when the virtual disk is degraded and a hot spare is not configured.
Details the process of initializing newly installed HDDs before they can be used with the NVR.
Explains how to set HDD properties to redundancy, read-only, or read/write (R/W) for data safety and reliability.
Explains how to check the status of installed HDDs on the NVR for immediate maintenance in case of failure.
Covers using HDD detection functions like S.M.A.R.T. and Bad Sector Detection to monitor HDD reliability.
To Next Page
