Need help?Do you have a question about the HIKVISION DS-7608NI-I2/8P and is the answer not in the manual?
General| Operating temperature (T-T) | -10 - 55 °C |
|---|---|
| Operating relative humidity (H-H) | 10 - 90 % |
| AC input voltage | 100 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (typical) | 15 W |
| Total Power over Ethernet (PoE) budget | 120 W |
| Networking standards | IEEE 802.3af, IEEE 802.3at |
| USB 2.0 ports quantity | 1 |
| Ethernet LAN data rates | 10, 100, 1000 Mbit/s |
| Power over Ethernet (PoE) | Yes |
| Ethernet LAN (RJ-45) ports | 9 |
| Supported network protocols | TCP/IP, DHCP, IPv4, IPv6, DNS, DDNS, NTP, RTSP, SADP, SMTP, SNMP, NFS, iSCSI, ISUP, UPnP, HTTP, HTTPS |
| Power over Ethernet (PoE) ports quantity | 8 |
| Number of fans | 1 fan(s) |
| Input bandwidth | 80 Mbit/s |
| Number of users | 64 user(s) |
| Output bandwidth | 256 Mbit/s |
| Maximum resolution | 3840 x 2160 pixels |
| Alarm input channels | 4 |
| Video input channels | 8 channels |
| Video formats supported | H.264, H.264+, H.265, H.265+, MPEG4 |
| Still image resolution(s) | 3840 x 2160, 1920 x 1080, 1600 x 1200, 1280 x 1024, 1280 x 720, 1024 x 768 |
| Analog signal format system | NTSC, PAL |
| Resolution at capture speed | 1920x1080@60fps |
| HDD capacity | 0 GB |
| HDD interface | Serial ATA |
| Maximum storage capacity | 12 TB |
| Number of HDDs installed | 0 |
| Number of HDDs supported | 2 |
| Certification | FCC Part 15 Subpart B, ANSI C63.4-2014 CE EN 55032:2015, EN 61000-3-2, EN 61000-3-3, EN 50130-4 |
| Product color | Black, Silver |
| Rack capacity | 1U |
| Wi-Fi | No |
Weight and Dimensions| Depth | 315 mm |
|---|---|
| Width | 385 mm |
| Height | 52 mm |
| Weight | 3000 g |
Offers advice on proper setup and handling to avoid potential issues and ensure optimal performance.
Covers configuration of alarms for events like video loss, tampering, and system exceptions.
Details how to set up PTZ parameters such as baud rate, data bit, and protocol.
Explains how to define and call PTZ presets, patrols, and patterns for automated camera movement.
Details how to set stream types, resolution, encoding, and other recording parameters.
Explains how to set up schedules for automatic recording and capture based on time or events.
Covers setting up motion detection areas, sensitivity, and trigger actions for recording.
Details how to configure recording triggered by external alarm inputs.
Explains how to set up recording triggered by Video Content Analysis (VCA) events.
Describes how to start, stop, and manage manual and continuous recording modes.
Explains how to enable redundant recording for enhanced data safety on a secondary HDD.
Details how to group HDDs to manage storage for specific channels or recording tasks.
Covers methods to protect record files from overwriting, such as locking files or setting HDD to read-only.
Explains how to search and play back recorded video files using various methods.
Explains methods for backing up files via quick export, normal search, or event search.
Guides users on managing USB drives, HDDs, and other storage devices used for backup.
Details the configuration of a hot spare device for system redundancy and data reliability.
Guides on configuring motion detection parameters, areas, and alarm response actions.
Explains how to configure handling actions for external sensor alarms.
Details how to configure alarms for video loss detection and set response actions.
Covers configuration of alarms for video tampering detection and response actions.
Describes how to configure handling actions for system exceptions like HDD errors or network disconnections.
Details the available alarm response actions such as event hints, full screen monitoring, and email notifications.
Guides on configuring face detection parameters, sensitivity, and response actions.
Details the setup for detecting vehicles and capturing license plates.
Explains how to configure virtual line crossing detection for people or vehicles.
Details the setup of IP addresses, DNS, working modes, and network interfaces.
Explains the process of initializing newly installed HDDs before use.
Offers solutions to common problems and error scenarios encountered with the NVR.
To Next Page
