Why is the Hiland Premium HLDS01-TSST burner flame is low?
A low burner flame on your Hiland Patio Heater can be due to several reasons. Low gas pressure is a common cause; turn the cylinder valve OFF and replace the cylinder. If the outdoor temperature is below 40ºF and the tank is less than 1/4 full, use a full cylinder. Also, inspect the burner and orifices for any blockages.
What to do if my Hiland Premium HLDS01-TSST pilot won’t light?
If the pilot light on your Hiland Patio Heater won't ignite, it could be due to a few reasons. There might be air in the gas line; open the gas line and bleed it (pressing control knob in) for no more than 1 - 2 minutes or until you smell gas. If the gas pressure is low with the cylinder valve fully open, turn the cylinder valve OFF and replace the cylinder. You can also try using a match to light the pilot, and consider obtaining a new igniter.
What to do if my Hiland Premium HLDS01-TSST burner won’t light?
If the burner won't light, it could be due to several reasons. First, the propane cylinder might be frosted over; wait until it warms up. Second, there might be a blockage in the orifice; clear any blockage. Third, the control knob might not be in the ON position; turn it to ON.
What to do if the pilot won’t stay lit on my Hiland Premium HLDS01-TSST?
If the pilot light won't stay lit, the issue could be due to: * Dirt built up around the pilot: Clean the dirt from around the pilot. * A loose connection between the gas valve and pilot assembly: Tighten the connection and perform a leak check. * A faulty thermocouple: Replace the thermocouple.
How to stop carbon build-up and thick black smoke from Hiland Premium HLDS01-TSST Patio Heater?
If you're seeing carbon build-up or thick black smoke from your Hiland Patio Heater, it's likely due to dirt or film on the reflector and burner screen, so clean them. Another cause could be a blockage in the burner; remove any blockage and clean the burner inside and outside.
How to fix carbon build-up and black smoke in Hiland Outdoor Fireplace?
Carbon build-up and thick black smoke in your Hiland Outdoor Fireplace may be caused by: * Dirt or film on the burner: Clean the burner. * A blockage in the burner: Remove any blockage and thoroughly clean the burner, both inside and out.
What to do if the igniter fails on my Hiland Patio Heater?
If the igniter fails, use a match to light the pilot. Obtain a new igniter and replace the old one.
What to do if there is low gas pressure with a fully open cylinder valve on my Hiland Patio Heater?
If you have low gas pressure even with the cylinder valve fully open, turn the cylinder valve OFF and replace the cylinder.
What to do if my Hiland Patio Heater burner won't light?
If the burner on your Hiland Patio Heater isn't lighting, there are a few things to check. First, if the propane cylinder is frosted over, wait for it to warm up. Also, check for any blockages in the orifice and clear them. Finally, make sure the control knob is turned to the ON position.
Why won't the burner light on my Hiland Patio Heater?
If the burner on your Hiland Patio Heater won't light, it could be due to a frosted propane cylinder; wait until the propane cylinder warms up and becomes unfrosted. Also, check for any blockage and clear it. Ensure that the control knob is turned to the ON position.
General| Model | HLDS01-TSST |
|---|---|
| Category | Patio Heater |
| Brand | Hiland |
| Heat Output | 48, 000 BTU |
| Fuel Type | Propane |
| Tank Capacity | 20 lbs |
| Ignition Type | Piezo ignition |
| Material | Stainless Steel |
| Height | 87 inches |
| Wheels | Yes |
| Heating Area | 200 sq. ft. |
| Fuel Tank | 20 lb |
| Safety Features | Automatic shut-off |
To Next Page