Hilti DG150 Safety Sheet

DIAMOND GRINDER
SAFETY SHEET
(Hilti DG150)
PLEASE READ THIS GUIDE CAREFULLY
BEFORE OPERATING THE EQUIPMENT
IMPORTANT - CONDUCT A RISK ASSESSMENT
Before you commence any work at your chosen work area, you should
undertake some preliminary hazard identication and risk control
precautions. Ideally more than one person should do this. This is
undertaken by:
1. Physically inspecting the work site
2. Reviewing the best way/job steps required to complete the task
3. Reviewing the Safe Work Information supplied with the equipment
4. Reviewing other reference documentation and expert advice.
The hazard identication and control process steps are dened as:
1. Identify the Hazards (eg. 240V power drill use around wet areas)
2. Assess the Risk (multi earth paths - possible electrocution)
3. Select the Control Measure (e.g. dry the area; use an RCD; use a
cordless drill etc)
4. Re-assess the Risk (risk of electrocution now negligible). This is
undertaken to ensure that the risk control measures adopted have not
introduced any new risks to the work area.
HELP AND SUPPORT
If the unit does not operate correctly or you are unhappy with its
performance, return it to Asset Construction Hire for an exchange,
or phone for assistance. Do not attempt repairs yourself.
Asset Construction Hire
Phone:1300 361 383 or email: o󰀩ce@assethire.com.au
OPERATION MANUAL
A PDF of the full Operation Manual is available at:
www.assethire.com.au/manuals-specs-safety-sheets/
and must be read before using the equipment.
BEFORE OPERATING THE EQUIPMENT:
• Read this Safety Sheet and any other information provided with the
equipment, including instructions, decals and operation guidelines.
• Check that you understand how and when the use the equipment,
and know how to operate it safely.
• Ensure that it is only used according to the manufacturers and hirer’s
instructions, and only for work that is compatable with its technical
limitations.
• Operate in a clear work area free from nonessential persons, children,
animals or hazards.
• Ensure that you have a secure footing and clear access and egress to
the work area while on the job.
• Do not operate any equipment if you are tired or su󰀨ering any medical
condition, or if under the inuence of drugs or alcohol which may
cause lethargy or dangers to yourself or others.
• Do not use faulty equipment. If in doubt contact Asset Construction Hire.
PERSONAL PROTECTION EQUIPMENT (PPE)
PROTECTIVE
GLOVES
HEARING
PROTECTION
SAFETY
GLASSES
RESPIRATORY
PROTECTION
PROTECTIVE
HELMET
PROTECTIVE
BOOTS
MAIN COMPONENTS
6 English
3 Description
3.1 Product overview
Printed: 24.11.2017 | Doc-Nr: PUB / 5139900 / 000 / 04
8 English
3.2 Tool components and controls
:
Pin wrench
∙
Clamping nut
Printed: 24.11.2017 | Doc-Nr: PUB / 5139900 / 000 / 04
English 9
$
Diamond cup wheel
£
Lamellar seal, small
|
Clamping flange
¡
Lamellar seal, large
Q
Retaining ring
W
Arbor
E
Locking ring
R
Guard bottom section
T
Guard top section
Z
Arbor lockbutton
3.3 Tool components, status indicators and controls
U
LED indicator
I
Supply cord
O
Locating lug
P
Carrying handle
Ü
Clip for power cord
[
Electrical socket with hinged cover
]
Latching lug
3.4 Intended use
The product described is an electrically powered diamond grinder. It is designed for professional use in
grinding mineral materials. The DG 150 grinder can be operated only in combination with the DPC 20 power
conditioner. Always use a dust extractor to ensure optimum dust removal.
The grinder is designed exclusively for dry abrasive removal of uncoated mineral materials and thin coatings
on concrete and similar mineral materials, with a maximum layer thickness of 3 mm (0.12 in).
3.5 Possible misuse
Do not use the product may in environments where there is a risk of explosion.
Do not use the product for wet grinding.
Do not use the product to work on hazardous or flammable materials (e.g. asbestos, magnesium, wood).
3.6 Items supplied
DG 150 grinder, DPC 20 power conditioner, clamping flange, clamping nut, pin wrench, operating instructions.
Other system products approved for use with this product can be found at your local Hilti Store or online at:
www.hilti.group | USA: www.hilti.com
4 Technical data
4.1 Technical data, DG 150
Rated speed, speed I
4,700 /min
Rated speed, speed II
6,600 /min
Weight of the DG 150 in accordance with EPTA procedure 01/2003
4.1 kg
Protection class (EN 60745 1)
Protection class II
(double-insulated)
Quick stop after power OFF
≤2s
Optimum gap between lamellar seal and work surface
0 mm …1 mm
Printed: 24.11.2017 | Doc-Nr: PUB / 5139900 / 000 / 04
English 7
@
On/off switch
;
Side handle
=
Guard, complete
%
Clamping band
&
Clamping lever
(
LED indicator
)
Machine supply plug
+
Speed selector switch (speeds 1 and 2)
§
Side-handle locking screw
/
Adjusting screw
Printed: 24.11.2017 | Doc-Nr: PUB / 5139900 / 000 / 04
English 7
@
On/off switch
;
Side handle
=
Guard, complete
%
Clamping band
&
Clamping lever
(
LED indicator
)
Machine supply plug
+
Speed selector switch (speeds 1 and 2)
§
Side-handle locking screw
/
Adjusting screw
Printed: 24.11.2017 | Doc-Nr: PUB / 5139900 / 000 / 04
8 English
3.2 Tool components and controls
:
Pin wrench
∙
Clamping nut
Printed: 24.11.2017 | Doc-Nr: PUB / 5139900 / 000 / 04
8 English
3.2 Tool components and controls
:
Pin wrench
∙
Clamping nut
Printed: 24.11.2017 | Doc-Nr: PUB / 5139900 / 000 / 04
English 9
$
Diamond cup wheel
£
Lamellar seal, small
|
Clamping flange
¡
Lamellar seal, large
Q
Retaining ring
W
Arbor
E
Locking ring
R
Guard bottom section
T
Guard top section
Z
Arbor lockbutton
3.3 Tool components, status indicators and controls
U
LED indicator
I
Supply cord
O
Locating lug
P
Carrying handle
Ü
Clip for power cord
[
Electrical socket with hinged cover
]
Latching lug
3.4 Intended use
The product described is an electrically powered diamond grinder. It is designed for professional use in
grinding mineral materials. The DG 150 grinder can be operated only in combination with the DPC 20 power
conditioner. Always use a dust extractor to ensure optimum dust removal.
The grinder is designed exclusively for dry abrasive removal of uncoated mineral materials and thin coatings
on concrete and similar mineral materials, with a maximum layer thickness of 3 mm (0.12 in).
3.5 Possible misuse
Do not use the product may in environments where there is a risk of explosion.
Do not use the product for wet grinding.
Do not use the product to work on hazardous or flammable materials (e.g. asbestos, magnesium, wood).
3.6 Items supplied
DG 150 grinder, DPC 20 power conditioner, clamping flange, clamping nut, pin wrench, operating instructions.
Other system products approved for use with this product can be found at your local Hilti Store or online at:
www.hilti.group | USA: www.hilti.com
4 Technical data
4.1 Technical data, DG 150
Rated speed, speed I
4,700 /min
Rated speed, speed II
6,600 /min
Weight of the DG 150 in accordance with EPTA procedure 01/2003
4.1 kg
Protection class (EN 60745 1)
Protection class II
(double-insulated)
Quick stop after power OFF
≤2s
Optimum gap between lamellar seal and work surface
0 mm …1 mm
Printed: 24.11.2017 | Doc-Nr: PUB / 5139900 / 000 / 04
English 9
$
Diamond cup wheel
£
Lamellar seal, small
|
Clamping flange
¡
Lamellar seal, large
Q
Retaining ring
W
Arbor
E
Locking ring
R
Guard bottom section
T
Guard top section
Z
Arbor lockbutton
3.3 Tool components, status indicators and controls
U
LED indicator
I
Supply cord
O
Locating lug
P
Carrying handle
Ü
Clip for power cord
[
Electrical socket with hinged cover
]
Latching lug
3.4 Intended use
The product described is an electrically powered diamond grinder. It is designed for professional use in
grinding mineral materials. The DG 150 grinder can be operated only in combination with the DPC 20 power
conditioner. Always use a dust extractor to ensure optimum dust removal.
The grinder is designed exclusively for dry abrasive removal of uncoated mineral materials and thin coatings
on concrete and similar mineral materials, with a maximum layer thickness of 3 mm (0.12 in).
3.5 Possible misuse
Do not use the product may in environments where there is a risk of explosion.
Do not use the product for wet grinding.
Do not use the product to work on hazardous or flammable materials (e.g. asbestos, magnesium, wood).
3.6 Items supplied
DG 150 grinder, DPC 20 power conditioner, clamping flange, clamping nut, pin wrench, operating instructions.
Other system products approved for use with this product can be found at your local Hilti Store or online at:
www.hilti.group | USA: www.hilti.com
4 Technical data
4.1 Technical data, DG 150
Rated speed, speed I
4,700 /min
Rated speed, speed II
6,600 /min
Weight of the DG 150 in accordance with EPTA procedure 01/2003
4.1 kg
Protection class (EN 60745 1)
Protection class II
(double-insulated)
Quick stop after power OFF
≤2s
Optimum gap between lamellar seal and work surface
0 mm …1 mm
Printed: 24.11.2017 | Doc-Nr: PUB / 5139900 / 000 / 04
English 9
$
Diamond cup wheel
£
Lamellar seal, small
|
Clamping flange
¡
Lamellar seal, large
Q
Retaining ring
W
Arbor
E
Locking ring
R
Guard bottom section
T
Guard top section
Z
Arbor lockbutton
3.3 Tool components, status indicators and controls
U
LED indicator
I
Supply cord
O
Locating lug
P
Carrying handle
Ü
Clip for power cord
[
Electrical socket with hinged cover
]
Latching lug
3.4 Intended use
The product described is an electrically powered diamond grinder. It is designed for professional use in
grinding mineral materials. The DG 150 grinder can be operated only in combination with the DPC 20 power
conditioner. Always use a dust extractor to ensure optimum dust removal.
The grinder is designed exclusively for dry abrasive removal of uncoated mineral materials and thin coatings
on concrete and similar mineral materials, with a maximum layer thickness of 3 mm (0.12 in).
3.5 Possible misuse
Do not use the product may in environments where there is a risk of explosion.
Do not use the product for wet grinding.
Do not use the product to work on hazardous or flammable materials (e.g. asbestos, magnesium, wood).
3.6 Items supplied
DG 150 grinder, DPC 20 power conditioner, clamping flange, clamping nut, pin wrench, operating instructions.
Other system products approved for use with this product can be found at your local Hilti Store or online at:
www.hilti.group | USA: www.hilti.com
4 Technical data
4.1 Technical data, DG 150
Rated speed, speed I
4,700 /min
Rated speed, speed II
6,600 /min
Weight of the DG 150 in accordance with EPTA procedure 01/2003
4.1 kg
Protection class (EN 60745 1)
Protection class II
(double-insulated)
Quick stop after power OFF
≤2s
Optimum gap between lamellar seal and work surface
0 mm …1 mm
Printed: 24.11.2017 | Doc-Nr: PUB / 5139900 / 000 / 04
English 9
$
Diamond cup wheel
£
Lamellar seal, small
|
Clamping flange
¡
Lamellar seal, large
Q
Retaining ring
W
Arbor
E
Locking ring
R
Guard bottom section
T
Guard top section
Z
Arbor lockbutton
3.3 Tool components, status indicators and controls
U
LED indicator
I
Supply cord
O
Locating lug
P
Carrying handle
Ü
Clip for power cord
[
Electrical socket with hinged cover
]
Latching lug
3.4 Intended use
The product described is an electrically powered diamond grinder. It is designed for professional use in
grinding mineral materials. The DG 150 grinder can be operated only in combination with the DPC 20 power
conditioner. Always use a dust extractor to ensure optimum dust removal.
The grinder is designed exclusively for dry abrasive removal of uncoated mineral materials and thin coatings
on concrete and similar mineral materials, with a maximum layer thickness of 3 mm (0.12 in).
3.5 Possible misuse
Do not use the product may in environments where there is a risk of explosion.
Do not use the product for wet grinding.
Do not use the product to work on hazardous or flammable materials (e.g. asbestos, magnesium, wood).
3.6 Items supplied
DG 150 grinder, DPC 20 power conditioner, clamping flange, clamping nut, pin wrench, operating instructions.
Other system products approved for use with this product can be found at your local Hilti Store or online at:
www.hilti.group | USA: www.hilti.com
4 Technical data
4.1 Technical data, DG 150
Rated speed, speed I
4,700 /min
Rated speed, speed II
6,600 /min
Weight of the DG 150 in accordance with EPTA procedure 01/2003
4.1 kg
Protection class (EN 60745 1)
Protection class II
(double-insulated)
Quick stop after power OFF
≤2s
Optimum gap between lamellar seal and work surface
0 mm …1 mm
Printed: 24.11.2017 | Doc-Nr: PUB / 5139900 / 000 / 04

Hilti DG150 Specifications

General

Brand	Hilti
Model	DG150
Category	Grinder
Language	English