How to fix Hitachi Server web console that does not start?
If the web console doesn't start, verify the connection between the management module and your console PC. Try reconnecting or replacing the LAN cable. You can also try typing the IP address into the web browser again.
What to do if the Hitachi Server Power LED is off or blinking amber and the console reports AC failure?
If the Power LED is off or blinking amber and the console reports AC failure, first verify that the power cord is properly connected to both the failed power supply and the AC source. If the issue persists, remove the failed power supply and replace it with a spare. If the Power LED lights up green after replacing the power supply, the process is complete.
Why is the Power LED of one power supply on my Hitachi Server solid amber and the console reports a power failure?
If the Power LED of one power supply is solid amber and the console reports a power failure, it indicates a power supply fault. Remove the failed power supply module and replace it with a spare. If the Power LED lights up green after the replacement, the process is complete.
What to do if the Active LED on my Hitachi Server is off or solid amber and the console reports a FAN failure?
If the Active LED is off or solid amber and the console reports a FAN failure, remove the failed fan module. Inspect the connector visually for damage. Reinstall it into the original bay. If the Active LED lights up green, the replacement is complete.
Why are the Power LEDs of all power supplies on my Hitachi Server solid amber, and the console reports Power failure?
If the Power LEDs of all power supplies are solid amber and the console reports Power failure, disconnect all power cords. Remove all power supplies and modules installed in the server chassis, and check all the connectors for damage.
What to do if a Hitachi Server blade does not power up and all LEDs are off?
If a server blade does not power up and all LEDs are off, remove the suspected server blade. Inspect the connector for damage. If there is no damage, install it into the original bay again.
What to do if the Hitachi Server Power LED doesn't stop blinking in green for more than 10 minutes, or the HEARTBEAT LED is off or solid green?
If the Power LED does not stop blinking in green for more than 10 minutes, or the HEARTBEAT LED is off or is solid green, push the Shutdown switch for about 4 seconds to power off the suspected management module. Wait for one minute, then push the Shutdown switch again to power it up.
How to fix a Hitachi Server switch module that doesn't power up and the Power LED is off?
If a switch module doesn't power up and the Power LED is off, remove the suspected switch module. Inspect the connector for damage. If there is no damage, install it into the original bay again.
Provides an overview of LPAR manager functions and modes.
Explains how hardware resources are logically partitioned.
Details the methods of dividing physical processors using scheduling modes.
Details specifying memory size allocation for each LPAR.
Explains methods for logically dividing physical PCI devices.
Details the four virtual NIC functions supported by LPAR manager.
Defines the network path for server operation and management.
Describes web console as a management module function for system console access.
Explains Hitachi Compute Systems Manager (HCSM) software for server chassis management.
Details managing virtualized logical servers using Server Conductor.
Provides functions for setting and changing LPAR manager/configuration.
Explains using higher-speed console than serial console for each LPAR.
Discusses redundancy of power supply and management modules.
Explains starting standby server blades automatically when active blades fail.
Explains how RBAC limits operations based on user roles.
Describes preventing unauthorized access using multiple accounts and authentication methods.
Explains audit log as a history of operations for detecting illegal activities.
Explains collecting memory data from a specified guest (LPAR).
Details collecting LPAR manager dump by executing a command.
Covers rapid recovery of systems using backup files after system failure.
Guides on obtaining LPAR manager firmware and performing version upgrades.
Explains migrating an LPAR from one server blade to another.
Describes configuration steps for LPAR manager after activation.
Guides on starting Tera Term and connecting to the LPAR manager screen.
Covers setting LPAR manager System time zone and NTP adjustment.
Explains how to add an LPAR on the Logical Partition Configuration screen.
Details saving made or changed settings on LPAR manager screens.
Describes how to activate an LPAR and boot the OS.
Explains setting the boot order through the remote console.
Explains deactivating an LPAR by shutting down the guest OS.
Guides on shutting down the LPAR manager system.
Discusses creating and keeping LPAR manager backup files safe.
To Next Page
General