How to fix Hitachi Server web console that does not start?
If the web console doesn't start, verify the connection between the management module and your console PC. Try reconnecting or replacing the LAN cable. You can also try typing the IP address into the web browser again.
What to do if the Hitachi Server Power LED is off or blinking amber and the console reports AC failure?
If the Power LED is off or blinking amber and the console reports AC failure, first verify that the power cord is properly connected to both the failed power supply and the AC source. If the issue persists, remove the failed power supply and replace it with a spare. If the Power LED lights up green after replacing the power supply, the process is complete.
Why is the Power LED of one power supply on my Hitachi Server solid amber and the console reports a power failure?
If the Power LED of one power supply is solid amber and the console reports a power failure, it indicates a power supply fault. Remove the failed power supply module and replace it with a spare. If the Power LED lights up green after the replacement, the process is complete.
What to do if the Active LED on my Hitachi Server is off or solid amber and the console reports a FAN failure?
If the Active LED is off or solid amber and the console reports a FAN failure, remove the failed fan module. Inspect the connector visually for damage. Reinstall it into the original bay. If the Active LED lights up green, the replacement is complete.
Why are the Power LEDs of all power supplies on my Hitachi Server solid amber, and the console reports Power failure?
If the Power LEDs of all power supplies are solid amber and the console reports Power failure, disconnect all power cords. Remove all power supplies and modules installed in the server chassis, and check all the connectors for damage.
What to do if a Hitachi Server blade does not power up and all LEDs are off?
If a server blade does not power up and all LEDs are off, remove the suspected server blade. Inspect the connector for damage. If there is no damage, install it into the original bay again.
What to do if the Hitachi Server Power LED doesn't stop blinking in green for more than 10 minutes, or the HEARTBEAT LED is off or solid green?
If the Power LED does not stop blinking in green for more than 10 minutes, or the HEARTBEAT LED is off or is solid green, push the Shutdown switch for about 4 seconds to power off the suspected management module. Wait for one minute, then push the Shutdown switch again to power it up.
How to fix a Hitachi Server switch module that doesn't power up and the Power LED is off?
If a switch module doesn't power up and the Power LED is off, remove the suspected switch module. Inspect the connector for damage. If there is no damage, install it into the original bay again.
Introduces logical partitioning and LPAR manager concepts.
Explains dedicated and shared resource partitioning methods.
Details processor scheduling modes (Dedicated vs. Shared).
Specifies memory allocation for each LPAR.
Details dedicated, shared, and exclusive shared PCI device assignment.
Covers Dedicated, Shared, VF, and Virtual NIC functions.
Provides functions for setting and changing LPAR configuration easily.
Simplifies setting and changing LPAR manager/configuration.
Covers redundancy of power supply and management modules.
Details equipping maximum 4 power supply modules for capacity.
Addresses attention items for non-redundant configuration.
Automatically starts standby server blade when active fails.
Limits operations based on user roles.
Prevents unauthorized access by users not permitted to access LPAR manager.
History of operations to detect and investigate illegal activities.
Improves security using TLS and certificates for authentication.
Collects memory data from specified guest (LPAR) for analysis.
Executes LPAR manager dump collection command for analysis.
Enables rapid recovery of systems via backup files after failure.
Saves configuration information to Management Module via Save Configuration operation.
Provides procedure for obtaining LPAR manager firmware and updating.
Details steps to start Tera Term and connect to the LPAR manager screen.
Covers setting LPAR manager System time zone and NTP adjustment.
Explains how to add an LPAR on the Logical Partition Configuration screen.
Describes how to activate an LPAR and boot the OS.
Details setting the boot order via remote console.
Explains operation of LPAR deactivation and its relation to server blade power.
Describes how to shut down the LPAR manager system.
Emphasizes creating and keeping backup files safe before operations.
Explains restoring LP configuration backup files and checking system time.
Details main keys and their functions for screen operations.
Explains activating an LPAR from the screen.
Explains deactivating an LPAR and its implications.
Details items and settings within the LPAR configuration screen.
Explains configuring logical processors for LPARs.
Displays physical processor configuration and status.
Assigns PCI devices to LPARs and manages their configuration.
Assigns Logical NICs to LPARs and configures network settings.
Configures LPAR manager system and user authentication.
Verifies if LPAR manager dump has been generated and saved.
Describes the procedure to collect LPAR manager dump data.
Provides notation and lists of audit log messages.
Lists system resources needed for LPAR manager startup.
Details failure conditions and activation workaround for memory fragmentation.
Explains system event logs and configuration changes during isolation/degradation.
Lists operating systems supported by LPAR manager.
Outlines functions supported by LPAR manager.
Lists LPAR manager setting items required for configuration.
Details port numbers used by LPAR manager for communication.
Shows recommended LPAR manager system configuration for SAN Boot.
Explains obtaining an overview of system operation using HvmGetPerf.
To Next Page
General