Hitachi CIW03-H - Page 23

5. Test Run
20
A16381TMF2
No. Item Optional Function
Individual
Setting
Setting
Condition
Contents Setting
147 rE
Setback Activating Temp. for Heat
Mode
×
00
01
02
03
04
05
06
07
08
09
15.0°C (59°F)
16.0°C (60°F)
17.0°C (62°F)
18.0°C (64°F)
19.0°C (66°F)
10.0°C (50°F)
11.0°C (52°F)
12.0°C (54°F)
13.0°C (56°F)
14.0°C (58°F)
148 rF
Setback Activating Temp. for Cool
Mode
×
00
01
02
03
04
05
06
07
08
09
10
26.0°C (78°F)
27.0°C (80°F)
28.0°C (82°F)
29.0°C (84°F)
30.0°C (86°F)
31.0°C (88°F)
32.0°C (90°F)
33.0°C (92°F)
34.0°C (94°F)
35.0°C (95°F)
25.0°C (77°F)
149
S1
(*15
)
Econo outside air high humidity
control
-
00
01
Unavailable
Available
150 S2 24-hour ventilation control -
00
01
Unavailable
Available
151 S3 NightPurge control -
00
01
Unavailable
Available
152 S4 Fan control based on CO2 sensor -
00
01
Unavailable
Available
153 S5
Rapid ventilation control at the
start of operation
-
00
01
Unavailable
Available
154 S6 Humidier drying operation -
00
01
02
90 min
180 min
Unavailable
155 S7 Suction humidity level setting -
00
01
02
03
Unavailable
High
Med
Low
156 S8 Suction humidity control setting -
00
01
02
Standard
High Humidity
Low Humidity
(*1): Even if temperature sensor selection is changed through "P3" setting, the compensation value will not be changed automatically. Please
change b1 setting according to temperature sensor selection.
(*2): The default temperature compensation is +2°C for Floor Exposed type & Floor Concealed type.
(*3): The "02", "03", "04" settings may not be available depending on the type of indoor unit. When connecting multiple indoor units, do separate
settings.
(*4): Standard type.
(*5): It is not applicable for Auto mode.
(*6): If Duct type models, 00: Increasing fan speed 1 (standard), 01: Increasing fan speed 2 (high static pressure), 02: Standard (low static
pressure).
(*7): Since it depends on the model, please refer to the Service Manual of each model.
(*8): If the set temperature is changed and kept within the set time at "F4", the temperature is automatically changed to "F5" and "F6". (If the set
temperature is out of range at "F5" and "F6", it is applied within the upper and lower limits for the set temperature.)
(*9): Applicable to the fan, cooling and dry operation modes.
(*10): Applicable to the heating operation mode.
(*11): When the unit is restarted by the controller, the temperature automatically changes to the setting temperature of "F5" or "F6".
(*12): Available only for 4-Way Cassette Type, 4-Way Cassette Compact Type, 2-Way Cassette Type, 1-Way Cassette Type, Ceiling Type.
(*13): Setting "P4" to "01", then the temperature of selected thermistor (sensor) can be shown.
(*14): Setting "01" can show sensor temperature selected in "P3".
(*15): Items "S1~S8" are available only for new econo-fresh units.