Hitachi HDS722580VLSA80

To Next Page

Page 1 version 1.1

Quick installation guide

Hitachi Deskstar 7K250

Serial ATA Hard disk drive

Models: HDS722580VLSA80

HDS722512VLSA80

HDS722516VLSA80

HDS722525VLSA80

System Requirements for Serial ATA

The following are needed to install a Serial ATA drive to

a system.

y Serial ATA capable motherboard or controller card

y Serial ATA drive

y Serial ATA cable (1 meter or less in length)

Handling precautions

Set the drive down gently to prevent damage from

impact or vibration.

• Do not open the ESD bag containing the drive

until needed.

• Handle the drive carefully by the edges. Do not

touch the exposed printed circuit board or any

electronic components.

• Do not press on the top or bottom of the drive.

• Before handling the drive, discharge any static

electricity from yourself and your clothing. With

one hand touch an unpainted metal surface on

your computer chassis, then touch the ESD bag

with the other hand. Remain in contact with the

chassis and the bag for a minimum of two

seconds.

Quick installation procedure

Note: Back up all data before installing drive!

1. Turn off the computer.

2. Unplug the computer.

3. Remove the computer cover as instructed by the

computer system manual.

4. Discharge static electricity (see Handling pre-

cautions).

5. Note the mounting position of existing drives and

cables. If you are replacing a drive or any cable,

remove it now.

6. Remove the drive from the ESD bag.

7. Record the model, the part number, and the serial

number of the drive for future reference.

8. Attach the Serial ATA cable to the drive. Match

key on cable to connector on drive

Connect Power Connector

Connect Serial ATA power connector if provided on

power supply or use legacy 4 pin power connector.

Arrange cable to match connector as shown in photos

below.

Need help?

Do you have a question about the Hitachi HDS722580VLSA80 and is the answer not in the manual?

Summary

System Requirements for Serial ATA

Installation Steps

Mount and Connect Drive

Securely mount the drive, verify all attachments, and reconnect the computer cover.

Verify BIOS Recognition

Ensure the BIOS recognizes the hard disk and its full capacity, adjusting settings if needed.

Partition and Format

Use the operating system utility to partition and format the drive before OS installation.

Summary

System Requirements for Serial ATA

Installation Steps

Mount and Connect Drive

Securely mount the drive, verify all attachments, and reconnect the computer cover.

Verify BIOS Recognition

Ensure the BIOS recognizes the hard disk and its full capacity, adjusting settings if needed.

Partition and Format

Use the operating system utility to partition and format the drive before OS installation.

This document serves as a quick installation guide for the Hitachi Deskstar 7K250 Serial ATA Hard Disk Drive. It provides essential information for setting up and maintaining the device, including system requirements, handling precautions, installation steps, and important warnings.

Function Description:

The Hitachi Deskstar 7K250 is a Serial ATA (SATA) hard disk drive designed for data storage within computer systems. It connects to a computer's motherboard or controller card via a SATA cable and receives power through a SATA power connector or a legacy 4-pin power connector. The drive's primary function is to store digital data, which can then be accessed, read, and written by the computer's operating system. Once installed and recognized by the system's BIOS, the drive needs to be partitioned and formatted before it can be used to install an operating system or store user data.

Important Technical Specifications:

The Hitachi Deskstar 7K250 series includes several models, each likely differing in storage capacity. The specific models listed are:

HDS722580VLSA80
HDS722512VLSA80
HDS722516VLSA80
HDS722525VLSA80

While the exact capacities are not detailed, the model numbers suggest varying storage sizes within the 7K250 series. The "7225" likely indicates a 7200 RPM rotational speed and a 250GB base capacity, with the subsequent numbers denoting variations. The "SA80" suffix indicates a Serial ATA interface. The drive requires a Serial ATA cable (1 meter or less in length) for data connection and a Serial ATA capable motherboard or controller card.

Usage Features:

Serial ATA Interface: The drive utilizes the Serial ATA interface, offering modern connectivity and data transfer speeds compared to older PATA (IDE) drives.
Compatibility: It requires a Serial ATA capable motherboard or controller card, ensuring compatibility with contemporary computer systems.
Flexible Power Connection: The drive can be powered either by a dedicated Serial ATA power connector from the power supply or by a legacy 4-pin power connector, offering flexibility depending on the power supply's available connectors. However, a critical warning emphasizes not to use both power connections simultaneously, as this will result in drive failure.
BIOS Recognition: For proper operation, the drive must be recognized by the system's BIOS, reporting its full capacity. The guide advises setting BIOS options to "Auto Detection" and "LBA mode" if available, should the drive not be recognized initially.
Partitioning and Formatting: After BIOS recognition, the drive needs to be partitioned and formatted using the operating system's setup utility before it can be fully utilized for data storage or operating system installation.

Maintenance Features:

Handling Precautions: The guide stresses several critical handling precautions to prevent damage and ensure the longevity of the drive:
- Gentle Placement: Always set the drive down gently to avoid damage from impact or vibration.
- ESD Protection: Do not open the Electrostatic Discharge (ESD) bag until the drive is needed. Before handling, discharge static electricity by touching an unpainted metal surface on the computer chassis and then the ESD bag for a minimum of two seconds. This prevents electrostatic discharge from damaging sensitive electronic components.
- Physical Contact: Handle the drive carefully by its edges, avoiding contact with the exposed printed circuit board or any electronic components. Do not press on the top or bottom surfaces of the drive.
Data Backup: A crucial note advises users to "Back up all data before installing drive!" This highlights the importance of data integrity and preparation before any hardware installation that might affect existing data.
Model and Serial Number Record: Users are advised to record the model, part number, and serial number of the drive for future reference. This information is vital for warranty claims, technical support, or future upgrades.
Cable Management: The guide suggests arranging cables to match the connector as shown in the provided photos, implying good cable management practices for optimal airflow and ease of access within the computer case.
Firmware/Software Updates: While not explicitly detailed as a maintenance feature, the mention of "www.hgst.com/support" for additional information implies that users might find resources for drivers, firmware updates, or troubleshooting guides online, which are common aspects of drive maintenance.

In summary, the Hitachi Deskstar 7K250 is a standard Serial ATA hard disk drive designed for reliable data storage. Its installation and maintenance require careful attention to handling precautions, proper power and data connections, and correct BIOS configuration to ensure optimal performance and longevity. The guide emphasizes the importance of ESD protection, gentle handling, and proper power connection to prevent damage and ensure successful operation.