Holder C250 User Manual

273 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

OPERATING MANUAL

C series

Table of Contents

Title1
Table of Contents2
Preface10
- General Information on Service11
- Explanations of the Terms Used12
Information about the Vehicle13
- Intended Use13
- Location for Use13
- Impermissible Use14
- Residual Dangers, Residual Risks14
- Warning15
- EC Conformity Declaration in Compliance with EC Directive 2006/42/EC16
- Information about Disposal16
- Positions of the Safety Symbols17
Information on Operation18
- Driving License18
- Overview of Driving Permit Classes18
Safety Rules22
- Safety Rules in General22
- Work Clothing22
- Safety Instruction for Retrofitting23
- C25023
- Gearbox Oil, Engine Oil, Diesel Fuel24
- Hydraulic Fluid, Brake Fluid25
- Battery Acid26
- Emissions27
- Exhaust Gas27
- Battery27
- Heat27
- Working in the Vicinity of Overhead Power Lines28
- Cab28
Technical Data30
- Vehicle Dimensions/Dimension Sketch C25030
- Dimensions C250, C27032
- Axle Loads34
- Permissible Gross Weight36
- Tyres37
- Track Widths38
- Theoretical Road Speed39
- Engine Technical Data40
- Assemblies: Drive41
- Assemblies: Hydraulics42
- Assemblies: Brakes, Lifts43
- Assemblies: Electrics, PTO44
- Assemblies: Vehicle45
- Noise Level Db (A)46
Description47
- Vehicle Overview, from Front Left47
- Vehicle Overview, Right Rear48
- Cab Views49
- Operating Elements from Driver's Seat50
- Multifunction Display51
- Right-Hand Operating Console (with Small Joystick)52
- Right-Hand Operating Console (with Large Joystick)54
- C25055
- Operating Elements from Driver's Seat, Foot56
- Operating Elements in the Operating Console57
- Right Front Upper Bar, Console Control Ele- Ments58
- Engine Speed Fine Adjustment Control59
- Operating Elements to the Right of the Op60
- Operating Elements Behind the Seat, con60
- Operating Elements Upper Front End of Cab62
- Operating Elements Rear Front End of Cab63
- Operating Elements64
- Operating Elements65
- Emergency Exit66
- Installation Rules for Labels67
- Label Positions68
- Standard Scope of Supply C250-C37070
Start-Up71
- Daily Checks and Activities before Start-Up71
Accessibility (Left and Right Side)72
Accessibility (from Above)73
Operating the Battery Disconnect Switch74
Checking Tyre Pressure75
Checking the Hitch Device76
Check the Lighting and the Rear View Mirrors76
Checking and Cleaning the Air Intake Channel77
Checking Radiator, Condenser* and Dirt Screen78
Checking Engine Oil Level79
Adding Engine Oil80
Check Hydraulic Oil Level81
Checking Coolant82
Refilling Washing Water84
Checking Brake Fluid Level85
Fuelling (Diesel)86
Check before Entering the Vehicle87
Adjusting Steering Column87
Driver and Passenger Seats88
- C25089
- Adjusting the Lumbar Support (16), Drivers Seat91
- Adjusting Right Operating Console92
- Instructions for Starting the Engine93
- Start Engine94
- Checking Braking and Steering Function96
- Service Brakes96
Operation97
- Before Driving97
- Driving on Slopes98
- Safety Belt99
- Instructions for Driving100
- Driving Mode with Hydrostat101
- Table of Ranges102
- Table of Driving Programmes 1)103
- Speeds for Road Driving104
- Speeds for Working105
- Adjusting the Fine Adjustment Wheel106
- Driving Mode with the Special Drive Sys108
- Tem108
- Pressing Inch Pedal110
Steering112
Brakes114
- Differential Lock116
- Windscreen Wiper, Windscreen Washer118
- Overview of the Lighting119
- Switching on Lighting120
- Signalling a Turn122
- Operating the Hazard Warning Flasher123
- Switching the Beacon on124
Switching on the Mirror Heater125
- Switch on Front, Rear Work Spotlight126
- Connecting Equipment to the Vehicle Socket127
- Radio* and Speakers128
- Operating the Driver's Cab Roof Hatch129
- Operating Interior Lighting130
- Heatable Windscreen131
- Switching on the Seat Heater132
- Heating and Ventilating the Cab133
- Operating the Air Conditioner135
- C250136
- Stationary Mode Operation138
- Stationary Mode Removal of Oil139
- Adjusting the Track140
Attachments141
- Permissible Gross Weight143
- Tions145
- Front and Rear Combination Table147
- Signal Socket148
- Attaching Implements149
- Lateral Adjustment of the Lift150
- Adjusting the Top Link Slide151
- Attaching Implements152
- Connecting Hydraulic Lines153
- Attaching Cardan Shafts155
- Detaching Attachments156
- Attachments, Cargo Bed Tipping System157
- Safety Notes for Operating Hydraulic Devices and Attachments158
- Adjusting Volume Flow 0 to 25 L/Min159
- External Operation of the Front Lift160
- General Warnings for Operating the Hy Draulic Floating Position162
- Operating the Joystick163
- Operating the Front Lift (Joystick)164
- Front Lift Inclination Adjustment166
- Passive Inclination Adjustment167
- Front Lift Side Adjustment168
Hydraulic Functions Joystick170
- Operating the Green Hydraulic Connections with the Joystick171
- Blue, Green Hydraulic Connections172
- Electrohydraulic Implement Relief174
- Operating the Electrohydraulic Implement175
C250176
- Implement Relief Coding178
- Switching Degree of Relief (SP1) to Actual Pressure in the Hydraulic Cylinder179
- Tipping System*, Rear Lift180
- Manual Body Frame182
- Attachments with Overhead Discharge183
- Safety Instructions for PTO Shaft Operation184
- Front PTO Shaft Drive185
- Rear PTO Shaft Drive186
- Pump187
- Operating Volume Dividers I* and II188
- Operating the Implement Servopump190
- Trailers, Towing193
- Instructions for Hitching the Trailer194
- Non-Automatic Trailer Hitch195
- Automatic Trailer Hitch196
- Trailer Hitch with Ball Head197
- Driving with a Trailer198
Shut-Down199
- Parking the Vehicle200
- Transport, Loading201
- Towing202
  - Coding the Digital Km/H Display204
  - Fault Messages206
Fault Cause Remedy208
- Faults of the Hydraulic System and Steering213
- C250214
- Faults of the Working Hydraulics216
- Maintenance Instructions219
- Battery225
User Maintenance246
- Lower Dipped Beam and High Beam247
- Sition Light248
- Indicator Light, Parking Light, Tail Light249
- C250250
- Extended Shutdown251
- Recommissioning after the Shutdown252
Maintenance Data253
- Filling Quantities for C250, C270, C350 C370254
- Light Bulbs255
- Tightening Torques for Hexagon and Stud Bolts as Per DIN256
- Engine Technical Data257
- Maintenance Schedule259
- Regular Maintenance as Needed261
- Single Maintenance after 50 or 500 Operat Ing Hours262
- Maintenance Every 500 Operating Hours263
- Maintenance Every 1000, 2000, 3000 Oper265
- Maintenance Every Year, Every Two Years266
- Index267

Other manuals for Holder C250

Owner's Manual28 pages

Questions and Answers:

Need help?

Do you have a question about the Holder C250 and is the answer not in the manual?

Holder C250 Specifications

General

Brand	Holder
Model	C250
Category	Snow Blower
Language	English

Related product manuals