To Next Page

To Previous Page

English

EN DE ES IT PT NL SV DA NO FI HU CS RU RO PL SL HR ET LT LV SK BG

FR DE ES IT PT NL SV DA NO FI

FR EN ES IT PT NL SV DA NO FI

FR EN DE IT PT

NL SV DA NO FI

FR EN DE ES NL SV DA NO FI

FR EN DE ES IT NL SV DA NO FI

FR EN DE ES IT PT SV DA NO FI

FR EN DE ES IT PT NL DA NO FI

FR EN DE ES IT PT NL SV NO FI

FR EN DE ES IT PT NL SV DA FI

FR EN DE ES IT PT NL SV DA NO

HU CS RU RO PL SL HR

ET LT LV SK BG

FR EN DE ES IT PT NL SV DA NO FI

CS RU RO PL SL HR ET LT LV SK BG

HU RU RO PL SL HR

HU CS RO PL SL HR

HU CS RU PL SL HR

HU CS RU RO SL HR

HU CS RU RO PL HR

HU CS RU RO PL SL

ET LT LV SK BG

FR EN DE ES IT PT NL SV DA NO FI

HU CS RU RO PL SL HR

LT LV SK BG

ET LV SK BG

ET LT SK BG

ET LT LV BG

ET LT LV SK

TROUBLESHOOTING

  

Engine will not start. No spark. Clean or replace spark plug. Reset spark

plug gap. Refer to 

earlier in this manual.

[Make sure ignition switch Engine is flooded. With the ignition switch OFF, remove spark

is in the RUN(I) position]. plug. Move choke lever to run position

(pushed in completely) and pull starter cord

15 to 20 times. This will clear excess fuel from

engine. Clean and reinstall spark plug. Set

ignition switch to run ( l ) position. Push and

fully release primer bulb 10 times. Pull starter

three times with choke lever at run. If engine

does not start, move choke lever to FULL

choke and repeat normal starting procedure.

If engine still fails to start, repeat procedure

with a new spark plug.

Engine starts but will not Carburettor requires “L” Contact an authorised service centre for

accelerate properly. (Low jet) adjustment. carburettor adjustment.

Engine starts, then dies. Carburettor requires “L” (Low Jet) Contact an authorised service centre for

adjustment. carburettor adjustment.

Engine starts but will not run Carburettor requires “H” Contact an authorised service centre for

properly at high speed. (High jet) adjustment. carburettor adjustment.

Engine does not reach full speed Lubricant/fuel mixture incorrect. Use fresh fuel and the correct 2-cycle

and/or emits excessive smoke. lubricant mix ratio.

Air filter dirty. Clean air filter. Refer to Cleaning the Air

Filter in the Maintenance section of this

manual.

Spark arrester screen dirty. Clean spark arrestor screen. Refer to

Inspecting/Cleaning the Spark Arrestor

Screen in the Maintenance section of

this manual.

Carburettor requires “H” Contact an authorized service centre for

(High jet) adjustment. carburettor adjustment.

Engine starts, runs, and Carburettor requires adjustment Turn idle speed screw “T” clockwise to

accelerates but will not idle. to idle speed. increase idle speed. Refer to Adjusting the

 in the Maintenance section of

this manual.

Chain turns at idle. Carburettor requires adjustment Turn idle speed screw “T” counter clockwise

to idle speed. to decrease speed. Refer to Adjusting the

 in the Maintenance section of

his manual.

Air leak in the intake system. Contact an authorised service centre for a

rebuild kit.

Brand	Homelite
Model	HCS4245B
Category	Chainsaw
Language	English

Homelite HCS4245B User Manual

Table of Contents

Questions and Answers:

Homelite HCS4245B Specifications

Related product manuals