Honeywell GSMVLP5-4G User Manual

800-10344 12/11 Rev. A
GSMVLP5-4G/GSMVLP5CN4G
GSM and ILP5 Ethernet
Communications Modules
Installation and Setup Guide
Installing Communication Modules
Installing the GSMVLP5-4G/GSMVLP5CN4G in the LYNX Touch Series Control
Ensure that SIM card and the connector board are securely installed in the GSMVLP5-4G/GSMVLP5CN4G
before installing the module in the LYNX Touch.
1. Install the provided FCC/IC label (P/N 800-10341) on the control’s case back (refer to Figure 1).
5000-100-186-V1
800-10341 Label
800-10259 11/11 Rev A
FCC / IC STATEMENT
IC: 573F-LYNXTOUCH2
This device complies with Part 15 of the FCC Rules, and RSS 210 of IC. Operation is subject to the
following two conditions: (1) This Device may not cause harmful interference. (2) This device must
accept any interference received, including interference that may cause undesired operation.
IC MODEL: LYNXTOUCH2
FCC ID: CFS8DLLYNXTOUCH2
CONTAINS MODULE: FCC ID: QIPPH8 IC: 7830A-PH8 IC MODEL: PH8
Figure 1. FCC/IC Label Location
2. Release the LYNX Touch front case from the back case by depressing the two locking tabs at the top of the
unit with the blade of a medium size screwdriver (Refer to Figure 2).
3. Install the GSMVLP5-4G/GSMVLP5CN-4G into the LYNX Touch control front case. Ensure that the
connector board is properly seated into the receptacle on the control (Refer to Figure 2).
4. Secure the GSMVLP5-4G/GSMVLP5CN-4G with the three provided screws (Refer to Figure 2).
5. Enable the GSMVLP5-4G/GSMVLP5CN-4G device, configure alarm reporting and module supervision and
register the device. Refer to the “Program the Radio” and “Diagnostics” sections in the LYNX Touch Series
Installation and Setup Guide (P/N 800-10614 or higher).
For Documentation and Online Support: http://www.security.honeywell.com/hsc/resources/MyWebTech

Honeywell GSMVLP5-4G Specifications

General

Brand	Honeywell
Model	GSMVLP5-4G
Category	Control Unit
Language	English

Summary

Installing Communication Modules

GSMVLP5-4G/GSMVLP5CN4G Installation

Ensure SIM card and connector board are installed before installing the GSMVLP5-4G/GSMVLP5CN4G module in the LYNX Touch.

Installing the ILP5 Module

ILP5 Installation in LYNX Touch

Ensure the connector board and cable are securely installed in the ILP5 before installing the module in the LYNX Touch.

Electrical Specifications

GSMVLP5-4G/GSMVLP5CN-4G Specs

Details voltage input and current (idle, average, peak) for the GSMVLP5-4G/GSMVLP5CN-4G module.

ILP5 Module Specs

Details voltage input and current for the ILP5 module (100 Base T and 10 Base T with traffic).

Regulatory Statements and Warnings

FCC Class B Statement

Statement regarding FCC requirements and acceptable use for the equipment, including interference guidelines.

Industry Canada Class B Statement

Confirms compliance with Canadian ICES-003 for the digital apparatus.

FCC/IC Compliance

States compliance with FCC Rules Part 15 and IC RSS 210, including operational conditions.

RF Exposure Warning

Mandates minimum separation distance for the communications module to ensure RF safety.