Why my Hoover HBWOS 69TMET-80 Washer does not work / start?
To troubleshoot a Hoover Washer that won't start, ensure it's plugged into a working socket and that power is on. Test the wall socket with another appliance. Also, make sure the door is correctly closed, the correct program is selected, the start button is pressed, and that the washer isn't in pause or time delay mode.
What to do if water leaked on the floor near my Hoover HBWOS 69TMET-80?
If you see water leaked on the floor near your Hoover Washer, it might be due to a leak from the seal between the tap, supply hose, and fill valve. Replace the seal and tighten the hose connections correctly. Also, check that the front filter is correctly closed.
Why my Hoover HBWOS 69TMET-80 does not spin?
If your Hoover Washer isn't spinning, try these steps: remove the load, de-tangle it, reload it, and restart the spin program. If water hasn't completely drained, wait a few minutes. Check if the "no spin" function is selected and review the selected options for their impact on the spin cycle. Also, using too much detergent can impede spinning, so ensure you're using the correct amount.
How to stop strong vibrations / noises during the spin cycle of my Hoover HBWOS 69TMET-80 Washer?
If your Hoover Washer is making strong vibrations or noises during the spin cycle, it may not be fully leveled. Adjust the feet as needed. Also, ensure that the transport screws, rubber bungs, and spacer tubes were removed.
What to do if my Hoover HBWOS 69TMET-80 displays error E2?
If your Hoover Washer displays 'E2' or the LEDs flash twice, ensure the water supply tap is open and the supply hose isn’t bent, kinked, or trapped. Check that the drain pipe is at the proper height. Close the tap, unscrew the filler hose, and clean the anti-sand filter. Also, check the filter for clogs or foreign objects.
What to do if my Hoover Washer displays error E3?
If your Hoover Washer displays 'E3' or the LEDs flash three times, check that the filter is not clogged and free from foreign objects. Also, make sure the drain hose isn’t bent, kinked, or trapped, and ensure the home drainage system isn't blocked.
What to do if my Hoover HBWOS 69TMET-80 Washer displays error E7?
If your Hoover Washer displays 'E7' or the LEDs flash seven times, make sure the door is correctly closed and that clothes aren't preventing it from closing fully. If the door is locked, turn off and unplug the washing machine, wait 2-3 minutes, and reopen the door.
What to do if my Hoover HBWOS 69TMET-80 Washer displays error E4?
If your Hoover Washer displays 'E4' or the LEDs flash four times, ensure you are using the correct amount of detergent and that the detergent is designed for use in a washing machine.
General| Appliance placement | Freestanding |
|---|---|
| Loading type | Front-load |
| Product colour | White |
| Built-in display | Yes |
| Door colour | White |
| Drum material | Stainless steel |
| Motor type | Inverter |
| Rated capacity | 9 kg |
| Maximum spin speed | 1600 RPM |
| Spin-drying class | B |
| Washing class | A |
| Number of washing programs | 16 |
| Noise Level (Washing) | 51 dB |
| Delayed start timer | Yes |
| Delayed start | Up to 24 hours |
| Remaining time indication | Yes |
| Energy efficiency class | A+++ |
| Water consumption washing per cycle | 46 L |
| Water Consumption | 46 L |
| Width | 60 cm |
| Color | White |
| Control type | Rotary |
To Next Page
