How to remove scale from HotSpring Hot Spot SX?
If your HotSpring Hot Tub has scale buildup, it's likely due to high calcium content in the water, along with total alkalinity and pH levels that are too high. Adjust the total alkalinity and pH. If scale removal is needed, drain the spa, scrub off the scale, refill it, and balance the water.
Why is my HotSpring Hot Spot SX Hot Tub not heating up, but the jets and light are working?
Your HotSpring Hot Tub might not be heating because the pressure switch is open. This can happen if the filter is clogged, preventing water flow through the heater. Check for a clogged filter to restore water flow. The pressure switch should reset once the flow is restored. If the pressure switch trips frequently, it is recommended to call for service.
How to get rid of musty odor in HotSpring Hot Spot SX Hot Tub?
If your HotSpring Hot Tub is producing a musty odor, it could be caused by bacteria or algae growth. To address this, shock the spa with sanitizer. If the problem is visible or persistent, drain, clean, and refill the spa.
Why does my HotSpring Hot Spot SX Hot Tub smell like chlorine?
If you notice a chlorine odor coming from your HotSpring Hot Tub, it could be due to a high chloramine level or low pH. To address this, shock the spa with sanitizer or adjust the pH to the recommended range.
What causes eye irritation in HotSpring Hot Spot SX Hot Tub?
If you're experiencing eye irritation while using your HotSpring Hot Tub, it could be due to low pH or a low sanitizer level. Try adjusting the pH, and shock the spa with sanitizer while maintaining the proper sanitizer level.
How to fix weak jets in HotSpring Hot Tub?
If the jets in your HotSpring Hot Tub are weak or surging, there are a few potential causes. First, check the water level and add water if it's too low. Also, clogged filters or suction screens can restrict water flow, so clean them as needed. Finally, make sure the jet nozzles and air valve are open.
What to do if my HotSpring Hot Tub display shows "- - - - "?
If your HotSpring Hot Tub displays “- - - - “ and the POWER icon flashes, it indicates that the heater high limit thermostat has tripped. To resolve this, disconnect power to the spa for at least thirty seconds to reset the heater. If the issue continues, try cleaning the filter. If it still occurs after cleaning the filter, call for service.
What to do if my HotSpring Hot Tub has stains?
Stains in your HotSpring Hot Tub can be caused by: * Total alkalinity and/or pH being too low: Adjust the total alkalinity and/or pH. * High iron or copper in the source water: Use a metal deposit inhibitor.
How to remove organic buildup or scum ring around my HotSpring Hot Spot SX Hot Tub?
An organic buildup or scum ring around your HotSpring Hot Tub is likely due to a build-up of oils and dirt. Wipe off the scum with a clean rag. If the build-up is severe, drain the spa, use a spa surface and tile cleaner to remove the scum, and then refill the spa.
What to do if my HotSpring Hot Tub has cloudy water?
If you have cloudy water in your HotSpring Hot Tub, it could be due to several reasons: * Dirty filters: Clean the filters. * Excessive oils or organic matter: Shock the spa with sanitizer. * Improper sanitization: Add sanitizer. * Suspended particles or organic matter: Adjust the pH and alkalinity to the recommended range. * Overused or old water: Run the jet pumps and clean the filters, or drain and refill the spa.
General| Heater | 4kW |
|---|---|
| Ozone System | Optional |
| Shell Material | Polymer |
| Energy Efficiency | Certified to the APSP 14 national standard |
| Pump 1 | 1.5 HP |
| Filtration System | Tri-X |
| Lighting System | LED |
| Voltage | 240V |
| Cabinet Material | Polymer |
| Warranty | 5-Year Shell Structure |
| Pump | 1.5 HP |
| Filtration | Tri-X |
Covers essential safety warnings for children, electrocution, and general injury prevention.
Details risks related to hyperthermia, medication, health conditions, and hygiene.
Provides guidance on cleaning the spa shell and safe chemical handling practices.
Outlines requirements for spa placement, including foundation types and structural support.
Details voltage selection, wiring, and conversion procedures for spa power.
Explains how to properly level the spa and install the safety cover.
Provides specifications and overhead views for Tempo, Relay, and Rhythm spa models.
Offers specifications and overhead views for the SX and TX spa models.
Guides users through initial spa setup, refilling, heating, and system operation modes.
Explains the functions of the spa control panel, including modes, locking features, and display.
Details the control panel for SX/TX models and the operation of the optional audio system.
Covers methods for testing spa water and essential chemical handling safety.
Outlines procedures for balancing Total Alkalinity, Calcium Hardness, and pH.
Discusses maintaining proper sanitizer levels and the use of various water care systems.
Provides instructions for cleaning spa filters, pillows, and the acrylic shell.
Guides on caring for the spa cover, cabinet, and procedures for draining the spa.
Explains how to prepare the spa for cold weather and winter storage.
Addresses common spa operational problems and their solutions.
Provides solutions for issues related to water clarity, odor, and chemical balance.
Covers warranty information, liability disclaimers, and customer support contacts.
To Next Page
