73
System Error Codes
3System Error Codes
• Introduction......................................................................................................................75
• System Error Codes and Warnings - Explanation ..................................................................75
• Continuable and Non-Continuable Error Codes ....................................................................78
• 01.0:03 - Error impact I2C channel..............................................................................78
• 01.0:10 - Problem with the Sausalito PCA......................................................................78
• 01.1.10 - Problem with the Printmech PCA ......................................................................78
• 01.02:10 - ISS PCA Problem ........................................................................................78
• 02.01:10 - Problem with the Carriage PCA ....................................................................79
• 03:10 - Problem with the PSU ......................................................................................79
• 05.1:10 - Problem with the CPU Fan..............................................................................79
• 05.3:10 - Main memory size failure .............................................................................80
• 06.03 - NVM file has a bad CRC................................................................................80
• 06:10 - Main NVM failure ..........................................................................................80
• 08:11 - Connection problem with the Front Panel............................................................80
• 09.01:10 - TOMAS Error ............................................................................................. 81
• 11:10 - Connection problem with the Trailing cable......................................................... 81
• 14.01:00 - Temperature high on the Heat sink ............................................................... 81
• 14.02:00 - Current too high on the Dryer Assembly .......................................................82
• 14.03:00 - Current too high on the Curing Module ........................................................82
• 14.04:00 - AC Voltage too high on the Dryer Assembly .................................................82
• 14.05:00 - AC Voltage too low on the Dryer Assembly...................................................82
• 14.06:00 - One or more heaters are not connected .......................................................83
• 14.07:00 - Connection problem with Heaters Control assembly .......................................83
• 14.08:00 - No AC voltage in the Dryer Assembly..........................................................83
• 14.09:00 - Heaters Control PCA is not ready ................................................................84
• 14.10:00 - Open circuit on the Dryer Assembly..............................................................84
• 14.11:00 - Open circuit in the Curing Module ................................................................85
• 14.12:00 - Petisa Fan Fault ..........................................................................................85
• 14.13:00 - Current Leak in Drying Channel ...................................................................85
• 14.14:00 - Current leak in the Curing Module................................................................85
• 14.15:00 - Generic failure with the Heaters Control Assembly..........................................86
• 14.16:00 - AC voltage too high on the Curing Module ...................................................86
• 14.17:00 - AC Voltage too low on the Curing Module ....................................................86
• 15.01:00 Drying system warm up timed out ..................................................................87
• 15.02:00 - Drying system cool down time out................................................................87
• 15.03:00 - Drying system temperature too high .............................................................87
• 15.04:00 - Drying system temperature too low ..............................................................88
• 15.05:00 - Problem with the Drying System Temperature Sensor ......................................88
• 15.06:00 - Temperature error detected .........................................................................89
• 15.08:00 - Dryer fans not connected ...........................................................................89
• 15.09:00 - Drying fans failure .....................................................................................89
• 15.10:00 - Drying Assembly resistors incorrect ...............................................................90
• 16.01:00 - Curing Module warm up time out.................................................................90
• 16.02:00 - Curing system cool down time out................................................................ 91
• 16.03:00 - Curing system temperature too high ............................................................. 91
• 16.04:00 - Curing system temperature too low (below 5C).............................................. 91
• 16.05:00 - Problem with the Curing System Temperature Sensor ......................................92
• 16.06:00 - Temperature error detected.........................................................................92
• 16.08:00 - Curing System fans not connected ...............................................................93
• 16.09:00 - Curing System fans failure ..........................................................................93
• 16.10:00 - Curing Assembly resistors incorrect...............................................................93
• 21.02:10 - Problem with the Web Wipe motor ...............................................................94
• 21.03:10 - Electrical problem in the Web Wipe Motor....................................................94
• 21.05:03 - Web Wipe Assembly Drifting......................................................................94
• 21:10 - Problem in the area of the Service Station...........................................................94
• 21:13 - Problem in the Service Station ...........................................................................95
• 23:10 - Problem with pressurization in the APS ..............................................................95
• 23:10 - Problem with pressurization in the APS ..............................................................95
• 24:03 - Ink Seup Failure.............................................................................................95
• 24:10 - Ink Cartridge Broken Bag ................................................................................96
• 24.02:00 - Top Cover Fans array is not connected.........................................................96
To Next Page
Loading...