74 Chapter 3 System Error Codes
System Error Codes
• 24.03:00 - One of the Top Cover Fans not connected....................................................96
• 26.00:10 - Contact failure with Magenta Ink Cartridge...................................................97
• 26.01:10 - Contact failure with Yellow Ink Cartridge .......................................................97
• 26.02:10 - Contact failure with Black Ink Cartridge ........................................................97
• 26.03:10 - Contact failure with Cyan Ink Cartridge ........................................................98
• 26.04:10 - Contact failure with Light Magenta Ink Cartridge............................................98
• 26.05:10 - Contact failure with Light Cyan Ink Cartridge.................................................99
• 26:14 - An incorrect Ink Cartridge has been detected .....................................................99
• 27:14 - An incorrect Printhead has been detected...........................................................99
• 29:02 - Printhead Cleaning Cartridge almost finished ....................................................99
• 32:01.01 - The substrate printed on is too small ........................................................... 100
• 32:01.02 - Problem with the Take Up Reel................................................................... 100
• 32:01 - Take Up Reel disconnected............................................................................100
• 32:02 - Take Up Reel disconnected at initialization ...................................................... 101
• 41:03 - Limited electrical voltage at the Media Axis motor............................................. 101
• 41:10 - Electrical fault at the Media Axis motor ............................................................ 101
• 42:03 - Problem with the Scan Axis Motor.................................................................. 101
• 42:10 - Electrical fault in the Scan Axis area ............................................................... 102
• 43:10 - Problem with the Vacuum Fan ........................................................................ 102
• 44:10 - There is a problem with the Aerosol Fan .......................................................... 102
• 44:11 - Connection problem with the Aerosol Fan ........................................................ 103
• 45.01:00 - Rewinder Servo Shutdown ........................................................................ 103
• 45.02:10 - Rewinder inverse polarity .......................................................................... 103
• 45.03:00 - Rewinder driver system fault...................................................................... 103
• 46:03 - Primer Servo shutdown ................................................................................. 104
• 46:10 - Electrical fault in the Primer motor................................................................... 104
• 46:13 - Primer distance failed.................................................................................... 104
• 50:01 - OMAS Navigation failure ............................................................................. 104
• 50:03 - Internal electrical connection problem............................................................. 105
• 50.01:10 - Connection problem with OMAS................................................................ 105
• 50.01:11 - Error with Media Advance Sensor or with cable............................................ 105
• 50:11 - Media navigation problem............................................................................. 106
• 50:14 - Firmware version mis-match............................................................................ 106
• 50.02:10 - Problem with OMAS Controller PCA........................................................... 106
• 51:10 - An error has been detected with the Window Lock Sensor .................................. 107
• 51.01:10 - Problem with the Service Station door sensor ................................................ 107
• 52:01 - A problem with the Drop Detector .................................................................. 107
• 52:10 - A problem with the On/Off switch in the Drop Detector..................................... 107
• 53:10 - Problem with the Media sensor....................................................................... 108
• 54:10 - Problem with the Media lever sensor ............................................................... 108
• 55:10 - Problem with the Line Sensor.......................................................................... 108
• 56:10 - Analog encoder calibration has failed ............................................................ 108
• 58:10 - Problem with the Color Sensor ....................................................................... 109
• 61:01 - Problem with the format of the file ................................................................... 109
• 61:08.01 - Job is password protected ......................................................................... 109
• 61:09 - Communication with the RIP broken .................................................................110
• 63:04 - Network problem .........................................................................................110
• 63:05 - The raster data does not arrive quick enough ...................................................110
• 65:04 - I/O port problem .........................................................................................110
• 66:08 - Cannot print on the current type of media ........................................................ 111
•
71:19 - Mis-match of printer information ....................................................................... 111
• 72:04 - Generic firmware error .................................................................................. 111
• 73:03 - Problem with the Carriage encoder ................................................................. 111
• 74:01 - Error upgrading firmware file ..........................................................................112
• 74:04 - Request to upgrade the firmware..................................................................... 112
• 77:04 - Embedded Web Server internal software error..................................................112
• 78.01:04 - Media settings error..................................................................................112
• 78.02:01 - End of roll detected on the Rewinder...........................................................112
• 79:03 - Generic firmware error I ................................................................................113
• 79:04 - Generic firmware error II................................................................................113
• 81:01 - Problem with the Media Drive.......................................................................... 113
• 81:03 - Problem with setting the encoder position ......................................................... 113
• 82:01 - Media jam in the platen.................................................................................114
• 85:03 - Drive Roller encoder problem ......................................................................... 114
• 86:01 - Carriage servo shutdown ............................................................................... 114
• 93:11 - Unable to pressurize the IDS............................................................................114
To Next Page
Loading...