EasyManuals Logo

HP ELITE x2 1012 G1 Quickspecs

HP ELITE x2 1012 G1
37 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #32 background imageLoading...
Page #32 background image
QuickSpecs
HP Elite x2 1012 G1
Technical Specifications
Not all configuration components are available in all regions/countries.
c04895999 DA 15477 Worldwide Version 16 March 22, 2017
Page 32
3ft onto every side, angle and edge onto 2” of plywood over
steel over concrete.
Dust*
The dust test was performed in accordance with MIL-STD-810G,
Method 510.5, Procedure I. Test parameters were set so that the
unit was dusted with Arizona Road Dust for six hours while being
operated. Each cycle was one day (24 hours); ten cycles with the
temperature being cycled between 30°C (86°F) and 60°C (140°F);
and relative humidity was a constant 95%.
Vibration*
The vibration test was performed in accordance with MIL-STD-
810G, Method 514.6, Procedure I category 4. This test evaluated
the units performance after it has been subjected to higher
levels of vibration while in storage: Operational U.S. highway
truck exposure, 1000 mile Simulation and One hour/axis
duration.
Vibration 2*
The vibration test was performed in accordance with MIL-STD-
810G, Method 514.6, Procedure I category 24. This test
evaluated the units performance after it has been subjected to
higher levels of vibration while in storage: Non-operational 0.04
g2/Hz at 20-1000 Hz, -6 dB/octave at 1000-2000 Hz and One
hour/axis duration.
Shock*
The shock test was performed in accordance with IL-STD-810G,
Method 516.6.5, Procedure I. This test objective was to
determine whether the unit could be safely operated after being
exposed to sudden physical shock events while operational. For
this test, 3 shocks were performed across each axis and
direction for a total of 18 shocks -40Gs peak, 11ms.
Freeze/Thaw test*
The Freeze/Thaw test was performed in accordance with MIL-
STD-810G, Method 524.54 Procedure III. The objective of
this test was to determine whether the unit could be safely
operated after being exposed to a temperature drop of -10°C
(14°F) for two hours. Unit is removed and checked for operation.
Sand test*
The Sand test was performed in accordance with MIL-STD-810G,
Method 510.5 Procedure II
Explosive Atmosphere*
The Explosive Atmosphere test was performed in accordance
with MIL-STD 810G, Method 511.5 Procedure I.
*MIL STD 810G testing is not intended to demonstrate fitness for U.S. Department of Defense contract requirements or for
military use. Test results are not a guarantee of future performance under these test conditions. Damage under the MIL STD test
conditions or any accidental damage requires an optional HP Accidental Damage Protection Care Pack.
COUNTRY OF ORIGIN
China

Other manuals for HP ELITE x2 1012 G1

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP ELITE x2 1012 G1 and is the answer not in the manual?

HP ELITE x2 1012 G1 Specifications

General IconGeneral
Bus typeOPI
SteppingD1
Tjunction100 °C
Processor codeSR2EN
Processor cache4 MB
Processor cores2
Processor familyIntel® Core™ m3
Processor seriesIntel Core m3-6Y series
Processor socketBGA 1515
Processor threads4
Processor codenameSkylake
Processor frequency0.9 GHz
Processor cache typeSmart Cache
Processor manufacturerIntel
Processor package size20 X 16.5 mm
Conflict-Free processorYes
PCI Express slots version3.0
Processor boost frequency2.2 GHz
Processor operating modes32-bit, 64-bit
ECC supported by processorNo
Graphics & IMC lithography14 nm
PCI Express configurations1x2+2x1, 2x2, 1x4, 4x1
Supported instruction setsSSE4.1, SSE4.2, AVX 2.0
Thermal Design Power (TDP)4.5 W
Maximum number of PCI Express lanes10
Device typeTablet PC
Form factorSlate
Product colorSilver
Internal memory4 GB
Memory clock speed1866 MHz
Internal memory typeLPDDR3-SDRAM
Storage mediaSSD
Compatible memory cardsMicroSD (TransFlash)
Internal storage capacity180 GB
Display diagonal12 \
Touch technologyMulti-touch
Display resolution1920 x 1280 pixels
Graphics cardHD Graphics 515
On-board graphics card ID0x191E
On-board graphics card modelIntel® HD Graphics 515
Maximum on-board graphics card memory1.74 GB
On-board graphics card OpenGL version4.4
On-board graphics card base frequency300 MHz
On-board graphics card dynamic frequency (max)850 MHz
Rear camera typeSingle camera
Rear camera resolution (numeric)5 MP
Front camera resolution (numeric)2 MP
Country of originChina
Wi-Fi standards802.11a, Wi-Fi 5 (802.11ac), 802.11b, 802.11g, Wi-Fi 4 (802.11n)
Bluetooth version4.2
Top Wi-Fi standardWi-Fi 5 (802.11ac)
Battery capacity2800 mAh
Battery life (max)10 h
AC adapter power45 W
USB 2.0 ports quantity0
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity1
Sustainability certificatesENERGY STAR
PlatformWindows
Operating system architecture64-bit
Processor ARK ID88198
Intel Secure Key Technology version1.00
Intel Stable Image Platform Program (SIPP) version0.00
Weight and Dimensions IconWeight and Dimensions
Depth213.5 mm
Width300 mm
Height8.05 mm
Weight820 g

Related product manuals