Time value
1
First page stop Second page stop Third page stop
1,000 ms leading edge about 7 mm
(0.27 inch) past fuser nip,
135 mm (5.31 inches) of page
past the transfer roller
Leading edge about 65 mm
(2.55 inches) away from the
registration roller, trailing edge of
the page about 38 mm
(1.49 inches) away from leaving
the HCI (start the job from Tray 5)
NA
2,000 ms Leading edge about 170 mm
(6.69 inches) past the fuser nip
Leading edge about 18 mm (0.70
inch) past the transfer roller
Trailing edge just leaving the HCI
(start the job from Tray 5)
3,000 ms leading edge about 154 mm (6.06
inches) past the standard face
down exit rollers, trailing edge
almost past the stapler diverter
Leading edge about 75 mm (2.95
inches) past the fuser nip,
Trailing edge about 10 mm (0.39
inch) from the transfer roller
leading edge at the transfer roller
1
Use these values for a simplex print stop test. See Table 3-17 Troubleshooting menu on page 67.
Table 3-19 Print/stop test time values (duplex print jobs)
Time value
1
First page stop Second page stop Third page stop
0 ms Leading edge at TOP sensor
(SR5)
NOTE Opening the
print-cartridge door pulls
the sheet backward.
NA NA
1 ms Leading edge about 20 mm
(0.78 inch) past the TOP sensor
(SR5)
NA NA
2,000 ms Leading edge about 170 mm
(6.69 inches) past the fuser nip,
but not out far enough to move
back toward the duplexer
Trailing edge just leaving the HCI
(start the job from Tray 5)
NA
3,000 ms Leading edge entering the
duplexer, trailing edge about
60 mm (2.36 inches) past the
standard face down exit rollers
(just past the reverse point)
Leading edge about 30 mm (1.18
inches) past the top of the middle
right door
NA
5,000 ms Leading edge about 25 mm (0.98
inch) out of the duplexer with
second side already printed
ready to re-feed
Leading edge just prior to
entering the fuser nip, trailing
edge about 35 mm (1.37 inches)
from the transfer roller (half the
page contains toner)
Leading edge about 175 mm
(6.88 inches) past the HCI
(Tray 5) pick rollers, trailing edge
still at the ( HCI (Tray 5) pick
rollers (start the job from Tray 5)
8,000 ms Leading edge about 80 mm (3.14
inches) past the registration
roller, second side already
printed and fed from the duplexer
Leading edge about 60 mm (2.36
inches) into the duplexer, second
side already printed and reversed
Leading edge about 175 mm
(6.88 inches) past the HCI
(Tray 5) pick rollers, trailing edge
still at the ( HCI (Tray 5) pick
rollers (start the job from Tray 5)
10,000 ms Both sides fused, trailing edge
leaving the fuser area to delivery
First side fused, leading edge in
the duplexer, and the trailing
edge about 85 mm (3.34 inches)
from the duplexer
leading edge about 55 mm
(2.16 inches) past the transfer
roller (for first past print)
12,000 ms Stops in stapler, then auto ejects First pass fused (other blank),
leading edge in duplexer, and the
Leading edge entering the
duplexer, trailing edge about
Table 3-18 Print/stop test time values (simplex print jobs) (continued)
74 Chapter 3 Manage and maintain the device ENWW
To Next Page
Loading...