To Next Page

To Previous Page

Before repairing connectors, follow these steps:

▲ Prepare the monitor for disassembly. See Preparation for disassembly on page 10.

IMPORTANT:

• Repair Condition: Connector repair is only for out of warranty.

• Repairing must operate by professional repairers (Note) in repair center, not applicable for end user.

• Electrostatic protection is required when component replacement is required.

• The monitor meets ROHS, please use Lead-free solder wire for soldering.

• If Connector need to replace, must check specification and part number whether match the BOM and location.

• If connector need to replace, please insert new parts carefully because the near pin may cause short circuit by

inappropriate operate.

• DO NOT allow any liquid on the board. Water and moisture may cause short-circuit to the electronic

components and lead to malfunctions.

• The fusion point of Lead-Free solder is requested. Repairing with conventional lead wire may cause damage.

• Work quickly to avoid overheating the circuit board as soon as you confirm the steady soldering condition.

• Keep the soldering iron tip clean and well tinned and when replacing parts.

• A close inspection of the circuit board revealed look in good condition.

• After repaired, must connect source to each port to check Main board function is ordinary.

Note: (The requirement of professional repairers’ regulation by ERP lot5)

1) The professional repairer has the technical competence to repair electronic displays and complies with the

applicable regulations for repairers of electrical equipment in the Member States where it operates.

Reference to an official registration system as professional repairer, where such system exists in the Member

States concerned, shall be accepted as proof of compliance with this point.

2) The professional repairer is covered by insurance covering liabilities resulting from its activity, regardless of

whether this is required by the Member State.

HDMI 1 connector CN502

Repair the HDMI connector:

1) Use a soldering iron and a de-soldering pump to remove as much solder as possible from the pin.

Questions and Answers:

Need help?

Do you have a question about the HP OMEN 24 and is the answer not in the manual?

HP OMEN 24 Specifications

General

Haze rate	25 %
Color depth	8 bit
Color gamut	90 %
Pixel pitch	0.28 x 0.28 mm
Screen shape	Flat
Pixel density	93 ppi
Display diagonal	23.8 \
Surface hardness	3H
Anti-glare screen	Yes
Native aspect ratio	16:9
Vertical scan range	60 - 165 Hz
Horizontal scan range	30 - 210 kHz
sRGB coverage (typical)	99 %
Contrast ratio (typical)	1000:1
Display number of colors	16.7 million colors
Display diagonal (metric)	60.5 cm
Display brightness (typical)	300 cd/m²
Supported graphics resolutions	640 x 480 (VGA), 720 x 400, 800 x 600 (SVGA), 1024 x 768 (XGA), 1280 x 1024 (SXGA), 1280 x 720 (HD 720), 1280 x 800 (WXGA), 1440 x 900 (WXGA+), 1600 x 900, 1680 x 1050 (WSXGA+), 1920 x 1080 (HD 1080)
DisplayPort version	1.4
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Energy efficiency scale	A to G
Power consumption (max)	40 W
Power consumption (standby)	0.5 W
Power consumption (typical)	25 W
Package depth	164 mm
Package width	595 mm
Package height	407 mm
Package weight	9330 g
Pivot angle	-90 - 90 °
Tilt angle range	-5 - 23 °
Height adjustment	100 mm
Panel mounting interface	100 x 100 mm
Product color	Black
Country of origin	China
Market positioning	Gaming
HP segment	Home
AMD FreeSync type	FreeSync Premium

Weight and Dimensions