How to fix a faulty monitoring unit on Huawei SUN2000-3KTL-10KTL-M1 Controller?
A faulty monitoring unit in the Huawei Controller means that the flash memory is either insufficient or has bad sectors. To resolve this, turn off the AC output switch and DC input switch, and then turn them on after 5 minutes. If the alarm persists, replace the monitoring board or contact your dealer or Huawei technical support.
How to troubleshoot grid overvoltage on Huawei SUN2000-3KTL-10KTL-M1?
A grid overvoltage alarm on your Huawei Controller indicates that the grid voltage exceeds the upper threshold. Try these steps: 1. If the alarm is occasional, it could be a temporary grid issue. The SUN2000 should recover automatically once the grid stabilizes. 2. If the alarm persists, verify that the grid voltage is within the acceptable range. If it's not, contact your local power operator. If it is within range, you can adjust the grid overvoltage protection threshold using the mobile app, SmartLogger, or NMS, but only with the consent of the local power operator. 3. Also, check for peak voltage issues on the power grid; if the problem persists, contact the power operator.
What to do if Huawei SUN2000-3KTL-10KTL-M1 Controller reports grid loss?
If the Huawei Controller displays a grid loss alarm, it means a power grid outage has occurred, or the AC circuit is disconnected, or the AC switch is off. The alarm should clear automatically once the power grid recovers. You can also check if the AC circuit is disconnected or if the AC switch is turned off.
How to fix high string input voltage on Huawei Controller?
The high string input voltage on your Huawei Controller indicates that the PV array is not properly configured. Too many PV modules are connected in series, causing the PV string open-circuit voltage to exceed the maximum operating voltage. To resolve this, reduce the number of PV modules connected in series until the PV string open-circuit voltage is within the acceptable range. The alarm should disappear once corrected.
What to do if Huawei SUN2000-3KTL-10KTL-M1 shows string reverse connection?
The 'String reverse connection' error on your Huawei Controller indicates that the PV string polarity is reversed. To fix this, check if the PV string is connected in reverse. If it is, wait until the PV string current drops below 0.5 A, then turn off the DC switch and correct the PV string polarity.
What does 'Battery abnormal' mean on my Huawei Controller?
If your Huawei Controller is showing a 'Battery abnormal' message, it indicates a fault with the battery itself. Here's what to check: 1. If the fault indicator on the battery is steady on or blinking, contact the battery dealer. 2. Verify that the battery enabling, power, and communications cable connections are correct, and that the communications parameters are consistent with the RS485 configurations of the inverter. 3. Ensure the battery auxiliary power switch is turned on.
What to do if Huawei SUN2000-3KTL-10KTL-M1 Controller upgrade failed?
If the Huawei Controller displays 'Upgrade failed or version mismatch', it means the upgrade process was not completed successfully. Try performing the upgrade again. If it fails repeatedly, contact your dealer or Huawei technical support.
What causes grid voltage imbalance in Huawei SUN2000-3KTL-10KTL-M1 Controller?
A grid voltage imbalance alarm on the Huawei Controller indicates that the difference between grid phase voltages exceeds the upper threshold. Here's how to handle it: 1. If the alarm occurs occasionally, the power grid may be temporarily abnormal. The SUN2000 should recover automatically. 2. If the alarm persists, check whether the power grid voltage is within the acceptable range. If not, contact the local power operator. 3. If the alarm lasts for a long time, check the AC output power cable connection. 4. If the AC output power cable is correctly connected, yet the alarm persists and affects the energy yield of the PV plant, contact the local power operator.
What does abnormal grounding mean on a Huawei Controller?
Abnormal grounding on the Huawei Controller indicates that the neutral wire or PE cable of the inverter is not connected, or the output mode set for the inverter is inconsistent with the cable connection mode. Power off the inverter first (turn off the AC output switch and DC input switch, and wait for a period of time). Then: 1. Check whether the PE cable for the inverter is connected properly. 2. If the inverter is connected to a TN power grid, check whether the neutral wire is properly connected and whether the voltage of the neutral wire to ground is normal. 3. After powering on the inverter, check whether the output mode set for the inverter is consistent with the output cable connection mode.
Why is the grid frequency unstable on my Huawei Controller?
An unstable grid frequency alarm on the Huawei Controller indicates the power grid frequency change rate doesn't meet local power grid code requirements. Here's what you can do: 1. If the alarm is occasional, it may be a temporary grid issue, and the SUN2000 should recover automatically. 2. If the alarm persists, check whether the power grid frequency is within the acceptable range. If not, contact the local power operator.
General| Brand | Huawei |
|---|---|
| Model | SUN2000-3KTL-10KTL-M1 |
| Category | Controller |
| Language | English |
To Next Page
