Hunter Stoves HAWK 4 - User Manual

Other manuals for Hunter Stoves HAWK 4

Questions and Answers

R
Richard McdonaldSep 1, 2025
Why is tar coming from the flue joints of my Hunter Stoves Stove?
- A
  Anthony TrujilloSep 1, 2025
  If you notice tar coming from the flue joints of your Hunter Stoves Stove, it could be due to operating the appliance at continuous low temperatures. To resolve this, operate at a high temperature for short periods each time the appliance is used to avoid large build-ups of tars and creosotes. See user instructions for correct use of air control. Another cause may be using poor quality wood, so use dry seasoned wood (less than 20% moisture content).
S
Stacey RogersAug 31, 2025
What to do if my Hunter Stoves HAWK 4 Stove is over firing?
- A
  Anthony WaltersAug 31, 2025
  Over firing in your Hunter Stoves Stove may be caused by a high flue draught. In this case, speak to your installer. It can also be caused by air controls being left fully open, so close the air control to reduce output.
J
Jon HowardAug 30, 2025
Why does my Hunter Stoves Stove have excessive fuel consumption?
- D
  Dwayne GonzalesAug 30, 2025
  Excessive fuel consumption in your Hunter Stoves Stove can be attributed to a high flue draught, in which case you should speak to your installer. It can also happen if you are using over dry wood, so avoid using constructional timber or pallet wood.
A
Amanda BruceAug 29, 2025
How to prevent creosote build-up in the chimney of my Hunter Stoves HAWK 4?
- P
  pamela15Aug 29, 2025
  Creosote build-up in the chimney of your Hunter Stoves Stove is often caused by using wood with a moisture content over 20%. To prevent this, use dry seasoned wood (less than 20% moisture content). Additionally, operate the stove at a high temperature for short periods each time it's used to avoid large build-ups of tars and creosotes.
M
Michelle BishopAug 28, 2025
Why is the glass blackening on my Hunter Stoves HAWK 4 Stove?
- S
  Susan HallAug 28, 2025
  If the glass on your Hunter Stoves Stove is blackening, it could be due to several reasons. You might be using poor quality wood, so ensure you use dry seasoned wood. Another cause could be low flue draught, so speak to your installer. Also, check if you are using the air control incorrectly; refer to the user instructions for correct use of air control. Finally, the appliance may be operated at low temperatures continuously, so operate at high output for short periods and see the instructions for correct use of air control.
M
michellecolemanAug 27, 2025
Why are the firebricks/glass getting dirty in my Hunter Stoves HAWK 4 Stove?
- W
  William StewartAug 27, 2025
  If you notice dirty firebricks or glass in your Hunter Stoves Stove, it's likely due to using wood with a moisture content over 20%. To remedy this, use dry seasoned wood with less than 20% moisture content.
C
Carlos WebbAug 27, 2025
Why is my Hunter Stoves HAWK 4 producing smoke and small flames?
- M
  Michael NelsonAug 27, 2025
  If your Hunter Stoves Stove is producing smoke and small flames, the problem might be that you are using wood with a moisture content over 20%. To solve this, ensure you use dry seasoned wood with less than 20% moisture content.
M
Miss Jade SimpsonAug 25, 2025
Why does my Hunter Stoves HAWK 4 Stove have a short burn time?
- M
  mwolfeAug 26, 2025
  A short burn time in your Hunter Stoves Stove could be because you're using wood with a moisture content over 20%. To fix this, ensure you use dry, seasoned wood with less than 20% moisture content.
L
Larry BlackAug 25, 2025
Why is the heat output low on my Hunter Stoves Stove?
- S
  Stephen VegaAug 25, 2025
  If your Hunter Stoves Stove isn't producing enough heat, it could be due to a low flue draught. In this case, speak to your installer for advice on a suitable flue system. Another potential cause is using wet wood with a moisture content over 20%. Make sure to use dry, seasoned wood with less than 20% moisture content.