How to fix uneven raising or lowering of my HunterDouglas Window Blind?
To fix your HunterDouglas Window Blind that does not raise or lower evenly, check inside the headrail to ensure no obstructions are preventing the mechanism from turning. Also, check that the lift cords are not pinched or tangled.
Why are the lift cords stuck on my HunterDouglas LiteRise Window Blinds?
If the lift cords on your HunterDouglas Window Blinds are stuck or jammed, inspect the cords and the moveable pin within the cordlock mechanism inside the headrail. Ensure the cords can move without obstruction. If they're jammed, carefully use a screwdriver or needle-nose pliers to adjust the pin and free the cords.
How to fix HunterDouglas SimpleLift Window Blinds when the bottom rail is not level?
If the bottom rail of your HunterDouglas SimpleLift™ blinds is not level or the blind height is incorrect, ensure that the headrail and installation brackets are level and properly aligned. Adjust or shim the brackets as needed to achieve levelness. To level the blind, raise the low side of the bottom rail by turning the skew adjustment feature on the headrail clockwise using a coin or screwdriver while lifting the weight from the bottom rail. Turn the skew adjustment that is on the same side as the low side of the bottom rail. If the blind height is too long, turn all of the skew adjustment features clockwise to raise the entire bottom rail to the desired height while lifting the weight from the bottom rail.
What to do if HunterDouglas LiteRise lift cords are bunching?
If the lift cords are bunching by the safety cord connector on your HunterDouglas Window Blinds, ensure the slats are in the open position. Then, raise and lower the blind to help straighten the lift cords.
Why do my HunterDouglas LiteRise not raise evenly?
If your HunterDouglas Window Blind does not raise or lower evenly, check inside the headrail to ensure no obstructions are preventing the mechanism from turning. Also, verify that the lift cords are not pinched or tangled.
How to fix HunterDouglas SimpleLift blinds slats not stacking evenly?
If, when raising your HunterDouglas SimpleLift™ blind, the slats are not stacking evenly and are falling over the bottom rail, it means the blind was raised too quickly. Gently raise the bottom rail, allowing the lift cords time to retract. This will allow the slats to stack evenly on the bottom rail.
How to level the bottom rail on HunterDouglas SimpleLift window blinds?
To level the bottom rail or correct the blind height on your SimpleLift HunterDouglas window blinds, first check that the headrail and installation brackets are level and aligned; adjust or shim the brackets if necessary. To level the blind, raise the low side of the bottom rail by turning the skew adjustment feature on the headrail clockwise with a coin or screwdriver while lifting the weight from the bottom rail. Note: Turn the skew adjustment on the same side as the low side of the bottom rail. If the blind height is too long, turn all of the skew adjustment features clockwise to raise the entire bottom rail to the desired height while lifting the weight from the bottom rail.
What to do if my HunterDouglas Window Blind lift cords are stuck or jammed?
If the lift cords of your HunterDouglas Window Blind are stuck or jammed, check the cords and the moveable pin in the cordlock mechanism inside the headrail of the blind. Ensure the cords can move freely. If they are jammed, use a screwdriver or needle-nose pliers to move the pin and free the cords.
What to do if my UltraGlide HunterDouglas Window Blind lowering mechanism engages but the blind does not lower?
If the lowering mechanism of your UltraGlide HunterDouglas Window Blind engages and “clicks” but the blind does not lower, the UltraGlide mechanism might be caught between the raising and lowering functions. Simply pull the wand or cord vertically to slightly raise and reset the blind. Then, lower as usual.
What to do if my HunterDouglas SimpleLift™ Window Blinds slats are not stacking evenly?
If the slats of your SimpleLift™ HunterDouglas Window Blinds are not stacking evenly and are falling over the bottom rail, it means that the blind was raised too quickly. Gently raise the bottom rail to give the lift cords time to retract, and the slats should then stack evenly on the bottom rail.
General| Safety | Cordless Lift System: Enhanced safety for children and pets. |
|---|---|
| Design | Sleek |
| Type | blinds |
| Material Options | fabrics |
| Light Control | Varies by fabric/material; options for light filtering to room darkening. |
| Privacy Control | Varies by fabric/material; options for sheer to opaque. |
To Next Page
