Husqvarna 135 User Manual (English)

Other manuals for Husqvarna 135

Questions and Answers:

L
lesliecraigAug 20, 2025
How to fix Husqvarna 135 starting failure?
- M
  Melody DonovanAug 21, 2025
  If your Husqvarna Chainsaw fails to start, several factors could be the cause. It might be due to binding pawls, which can be resolved by adjusting, cleaning, or replacing them. Ensure you are using the correct fuel type; if not, drain the incorrect fuel and refill with the appropriate type. Also, check the spark plug: it should be dry, clean, and properly gapped. If the spark plug is loose, retighten it. Finally, adjust the idling speed using the T-screw.
P
Peter RuizAug 22, 2025
What to do if Husqvarna 135 Chainsaw engine starts but does not stay running?
- B
  Blake CrawfordAug 22, 2025
  If your Husqvarna chainsaw starts but doesn't stay running, consider these potential causes: ensure you're using the correct fuel type; if not, drain the incorrect fuel and replace it with the correct one. Check the air filter and clean it if it's clogged. Also, inspect the fuel filter and replace it if it's clogged.
M
Marc JenkinsAug 25, 2025
Why Husqvarna 135 Chainsaw won't start?
- W
  Wendy ObrienAug 25, 2025
  A Husqvarna chainsaw might fail to start due to several reasons: binding pawls, which may require adjustment, cleaning, or replacement. The fuel type could be incorrect, necessitating a drain and replacement with the correct fuel. The spark plug might be contaminated, wet, loose, or have an incorrect gap, requiring cleaning, drying, retightening, or gap adjustment. Adjust the idling speed with the T-screw.
G
Gregory RichardsAug 26, 2025
Why is my Husqvarna 135 difficult to start?
- J
  Julia JonesAug 27, 2025
  If your Husqvarna Chainsaw is hard to start, possible solutions include adjusting the L screw, or checking if the air filter, fuel filter, or fuel line are blocked. The choke may not be working, the choke pivot or valve may be worn, the piston ring may be seized, or the impulse channel may be blocked.
W
williamsmichaelAug 27, 2025
Why does my Husqvarna 135 Chainsaw engine stalls when throttle released?
- R
  Raven RamseyAug 28, 2025
  If your Husqvarna Chainsaw engine stalls when you release the throttle, consider these potential causes: You may need to adjust the L screw or the H screw. Other possible causes include a faulty pump diaphragm, a needle valve set too high, a sticking needle valve assembly, or faulty diffuser jets.
L
Lee KingAug 29, 2025
Why does my Husqvarna Chainsaw carburettor leaking fuel?
- C
  coxwilliamAug 29, 2025
  If your Husqvarna Chainsaw carburettor is leaking fuel, it could be due to a loose or faulty fuel pipe, a hole in the diaphragm, a worn needle valve, a needle valve assembly sticking, a needle valve set too high, a leak in the metering system, or a loose cover on the carburettor pump side.
D
Dr. Michael DayAug 31, 2025
How to fix Husqvarna 135 that will not idle?
- R
  Rickey AndersonAug 31, 2025
  If your Husqvarna Chainsaw won't idle, consider these solutions: Adjust the L screw. Check for a leaking air intake hose, loose carburettor mounting bolts, or a loose or faulty fuel hose. Inspect the fuel filter and fuel line for blockages. Also, check the fuel tank vent. Other potential issues include a stiff throttle valve pivot, a sticking throttle pushrod, a defective throttle return spring, a bent throttle stop, or a faulty diffuser jet.
T
Thomas JohnsSep 2, 2025
How to troubleshoot low power on my Husqvarna 135?
- W
  wilsonrebeccaSep 2, 2025
  If your Husqvarna Chainsaw has low power, try these solutions: Adjust the H screw. Check for blockages in the fuel tank vent or fuel filter. Inspect for a leaking or blocked impulse channel. Also, check for a loose cover on the carburettor pump side, a faulty pump diaphragm, or a blocked air filter. Other potential issues include a sticking needle valve assembly, a leak in the metering system, an incorrectly assembled metering system, a loose diaphragm rivet, a hole in the diaphragm, or a leaking control diaphragm/cover plate.
J
James SchmittSep 3, 2025
What causes a Husqvarna 135 to flood when the engine is not running?
- W
  William CarrSep 4, 2025
  If your Husqvarna Chainsaw is flooding when the engine isn't running, it might be due to a worn needle valve, a needle valve set too high, or a needle valve assembly sticking.
M
Michael JohnsonSep 5, 2025
What causes idling too rich on Husqvarna 135 Chainsaw?
- A
  Allison HardingSep 5, 2025
  If your Husqvarna Chainsaw is idling too rich, consider these possible causes: Adjust the L screw. Other potential issues include a worn needle valve, a needle valve set too high, a worn needle valve lever, a leaking control diaphragm/cover plate, or a needle valve assembly sticking.

Husqvarna 135 Specifications

General

Cylinder Displacement	40.9 cm³
Weight	4.4 kg
Sound Pressure Level	102 dB(A)
Sound Power Level	114 dB(A)
Bar Length	14 in
Chain Pitch	3/8 inch
Chain Gauge	0.05 in
Oil Tank Volume	0.25 liters