Why Husqvarna T536LiXP Chainsaw product starts immediately when battery is added?
If your Husqvarna Chainsaw starts immediately when the battery is added without pressing the keypad, it is likely due to a short circuit in the keypad. The solution is to replace the keypad.
Why is the warning indicator flashing on my Husqvarna Chainsaw?
The warning indicator flashes because of a temperature deviation. To resolve this, ensure the battery is used in surroundings where temperatures are between 5°C/41°F and 40°C/104°F.
What to do if the red error LED comes on on my Husqvarna Chainsaw?
The red error LED indicates that the cell difference is too much (1V). Speak to your servicing dealer.
Why Husqvarna Chainsaw won't start and no LEDs are on?
If your Husqvarna Chainsaw doesn't start and no LEDs light up when you press the power button, there could be several reasons. First, the battery might be defective; press the on/off button to check the battery – at least one green LED should illuminate. Other potential causes include a defective connection between the battery and the product (ensure the connectors are clean and undamaged), a faulty connection in the keypad connector (make sure it's correctly assembled, dry, undamaged, and free from corrosion), a broken keypad (replace it), damaged cables between the control unit and keypad/main switch (repair or replace them if damaged), or a short circuit in the control unit (replace it).
What does it mean if a warning sign flashes after start and product hangs up with green led on Husqvarna Chainsaw?
If a warning sign on the keypad flashes after starting your Husqvarna Chainsaw, and the product freezes with the green LED on, it could indicate a defective signal between the battery and the product. Ensure that the power connectors between the battery and the product are clean and undamaged. Also, check that the small cables between the connector and the control unit are not loose or damaged.
Why is the red error LED flashing on my Husqvarna T536LiXP Chainsaw?
The red error LED on your Husqvarna Chainsaw flashes because: * The battery is empty, so you should charge the battery. * There is a temperature deviation. Use the battery in temperatures between -10°C (14°F) and 40°C (104°F). * There is an overvoltage. Remove the battery from the battery charger.
What to do if a red warning sign flashes on the charger of Husqvarna T536LiXP?
If a red warning sign flashes on the charger of your Husqvarna Chainsaw when the battery is attached, it could be due to several reasons: a defective connection between the charger and battery (ensure the power plugs are clean and undamaged), the battery temperature being too high (let the battery cool in the charger for 1-5 minutes), the ambient temperature being too low (ensure it's above 5°C), the battery temperature being too low (ensure it's above 5°C), a defective battery (check by pressing the battery start button; at least one green LED should light up, if not, replace the battery), or a defective charger (disconnect the charger from the mains for 1 minute, then reconnect; the fan should start and a green LED should light up for 3 seconds, if not, replace the charger).
What to do if the warning indicator is flashing on my Husqvarna T536LiXP?
The warning indicator might flash on your Husqvarna Chainsaw due to several reasons: * The chain brake may be engaged. To solve this, pull back the front hand guard to release the chain brake. * There could be a temperature deviation. In this case, allow the product to cool down. * The cutting attachment might be jammed due to overload. If so, release the cutting attachment. * The power trigger and the activate button may have been pressed simultaneously. Release the power trigger to activate the product.
What does it mean if a warning sign on the keypad flashes after start on Husqvarna T536LiXP Chainsaw?
If a warning sign on the keypad of your Husqvarna Chainsaw flashes after you start it and then the product stops, it could be due to several reasons: the power trigger might have been pushed during start (avoid pushing the power trigger when starting the product), there might be water in the main switch signal connector (disassemble and dry the stop signal connector, then reassemble it), there could be a short circuit in the keypad (replace the keypad), or there might be a short circuit in the main switch (replace the main switch).
What does it mean if a warning sign shows a red light on Husqvarna T536LiXP keypad?
If a warning sign shows a red light on the keypad of your Husqvarna Chainsaw, it indicates that permanent error codes are preventing the product from running. Erase the error codes using a diagnostic tool. Alternatively, the control unit might be broken and need replacement.
General| Battery Voltage | 36 V |
|---|---|
| Chain Speed at Max Power | 20 m/s |
| Oil Tank Volume | 0.2 L |
| Power Source | Battery |
| Vibration Level (Rear Handle) | 3.5 m/s² |
| Chain Pitch | 3/8 inch |
| Chain Gauge | 1.3 mm |
To Next Page