Why is my Hypontech Inverter temperature too high?
The inverter temperature might be too high because the airflow to the heat sink is obstructed, the installation site is in direct sunlight, or the ambient temperature around the inverter is too high. If these conditions are normal, further assistance is needed.
What to do if my Hypontech Inverter shows a Grid voltage exceeds the permissible range error?
If this error occurs frequently but recovers automatically, check if the grid voltage is outside the permissible range due to local grid conditions. You can try modifying the monitored operational limits after informing the electric utility company first.
What should I check if my Hypontech HPT-8000 Inverter displays an Insulation to ground resistance error?
Check the PV array’s insulation to ground to ensure the insulation resistance is greater than 200K?. Also, visually inspect all PV cables and modules. Ensure the grounding connection of the inverter is reliable.
What to do if my Hypontech HPT-8000 Inverter displays a Ground fault circuit interrupter (GFCI) exceeds the permissible range?
Ensure the grounding connection of the inverter is reliable, and visually inspect all PV cables and modules. If the fault persists, further assistance is needed.
What to do if Hypontech HPT-8000 Inverter shows PV voltage too high?
Check the open-circuit voltages of the strings to ensure they are below the maximum DC input voltage of the inverter. If the input voltage is within the permissible range when the fault occurs, further assistance is needed.
How to fix Utility grid disconnected failed error on Hypontech HPT-8000 Inverter?
Confirm whether the AC circuit breaker is disconnected, whether the AC terminal or fuse is in good contact, and whether the power supply line is normal.
What to do if my Hypontech HPT-8000 displays a Bus-voltage too high error?
Check the open-circuit voltages of the strings and make sure it is below the maximum DC input voltage of the inverter. If the input voltage lies within the permissible range while the fault occurs, please contact the service.
What to do if my Hypontech HPT-8000 Inverter displays a AC current sensor abnormal in the process error?
Disconnect the inverter from the utility grid and the PV array, and reconnect it after the LED turns off. If the fault persists, further assistance is needed.
What to do if my Hypontech HPT-8000 displays a Ground fault circuit interrupter (GFCI) sensor error?
Disconnect the inverter from the utility grid and the PV array, and reconnect it after the LED turns off. If the fault persists, further assistance is needed.
Why does my Hypontech HPT-8000 show Grid frequency exceeds the permissible range?
If this occurs frequently but recovers automatically, confirm if the grid voltage is outside the permissible range due to grid frequency exceeding local grid conditions.
Outlines critical safety precautions to be followed before and during the commissioning process of the inverter.
A comprehensive checklist of safety checks to perform before energizing the inverter and starting operation.
Information on identifying and responding to an Earth Fault Alarm, including error code 6 and LED indication.
A guide listing all error codes, their descriptions, and recommended corrective actions for troubleshooting.
A critical safety warning regarding the high temperature of the heat sink during operation and cleaning precautions.
General| Max. DC Voltage | 1000 V |
|---|---|
| Number of MPPTs | 2 |
| Rated AC Power | 8000 W |
| Max. AC Power | 8800 VA |
| Rated AC Voltage | 230 V |
| AC Voltage Range | 180-280 V |
| THDi | <3% |
| DC Switch | Yes |
| Protection Degree | IP65 |
| Operating Temperature Range | -25°C to +60°C |
| Cooling | Natural Convection |
| Frequency | 50/60 Hz |
| MPPT Voltage Range | 200-800 V |
| Power Factor | 0.8 leading - 0.8 lagging |
| Output Voltage | 230 V |
| Efficiency | 98.2% |
| Protection Features | Overvoltage |
To Next Page