EasyManua.ls Logo

IDEAL 4305

IDEAL 4305
32 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
www.ideal.de
IDEAL 4305
Operating InstructionsGuillotines
ϞϴϐθΘϟ΍ΕΎϤϴϠόΗ
᧔ᦤᦸ᥸ᦿҫӇᦚᦸᦿҫҮ᧛Ҧ
Question and Answer IconNeed help?

Do you have a question about the IDEAL 4305 and is the answer not in the manual?

IDEAL 4305 Specifications

General IconGeneral
BrandIDEAL
Model4305
CategoryCutter
LanguageEnglish

Summary

Safety Precautions

General Safety Instructions and Prohibitions

Read manual, follow safety instructions, manual available at all times; no children operation, do not reach under blade.

Blade Handling and Material Warnings

Never leave blade unattended, do not transport blade without protection, danger of injury; do not cut hard or splintering materials.

Machine Usage and Safety Device Requirements

Machine purpose, one-man operation, mandatory safety devices; close guard, release lock, lower lever.

Blade Lever Locking and Cutting Conditions

Return lever to top, locking secures blade, cutting requires closed guard and released lock; danger of placing hands under unlocked blade.

Installation

Stand Assembly and Setup

Unpack stand, assemble according to instructions, lift machine with two people, secure blade lever.

Attaching Backgauge, Levers, and Tool Set

Screw on backgauge crank, handle, and clamping lever found in the tool set.

Operation

Operating Elements Overview

Identifies and describes machine components A through M.

Pre-Operation Checks and Requirements

Understand instructions, check safety devices, mount all covers, conditions for cutting release.

Setting Cutting Measurement

Set measurement using backgauge crank, fine adjustment with calibration ring, scale explanation.

Preparing for Cutting

Prevent accidental adjustment, lock blade lever, place paper against backgauge and side lay.

Initiating the Cutting Process

Engage clamp, lower guard, release lock, pull blade lever down.

Post-Cutting Procedures

Lock blade lever, move clamp lever, lift guard, remove cut paper.

Blade and Cutting Stick Replacement

Blade Quality, Safety, and Handling

Blade quality issues, replacement needs, danger of injury, sharp blade handling, trained staff only.

Blade Removal from Front

Secure blade lever, lift front guard, remove blade screws from elongated holes.

Cutting Stick Inspection and Replacement

Inspect, turn, or exchange cutting stick; usage limits and post-exchange clamp closure.

Blade Tool Attachment and Blade Removal

Attach blade changing tool, screw tightly, remove blade screws, push and lower blade to remove.

New Blade Handling and Positioning

Take new blade from box, screw to tool, cover blade edge.

Blade Positioning and Spring Adjustment

Place exchanged blade into carrier, push to top/left, push springs back if needed for polished blade.

Securing New Blade Screws

Push blade changing tool up, tighten middle screw, then left/right screws, remove tool.

Final Blade Screw Tightening and Depth Adjustment

Lightly tighten blade screws, turn blade depth adjustment knob fully right.

Checking and Adjusting Cutting Depth

Open clamp, place paper, lower blade lever, turn depth adjustment knob to cut paper width.

Cutting Depth Safety

Danger of injury, blade must always be covered by clamping bar.

Securing Blade Lever and Front Guard

Move blade lever up and secure, lift front guard, tighten screws.

Maintenance and Cleaning

Maintenance Personnel and Lubrication

Maintenance by trained staff only, lubricate movable parts with non-resinous grease, clean before lubricating.

Blade Lever Adjustment and Cover Removal

Blade lever should not fall, tighten hexagon screw, remove cover and screws, adjust blade depth setting if altered.

Possible Malfunctions and Troubleshooting

Machine Not Functioning Cut Failure

If machine doesn't function or cut fails: close front cover, release blade lock, pull blade lever.

Incomplete Cutting

If last sheet isn't cut: turn/reverse cutting stick, re-adjust blade depth if needed.

Poor Cutting Quality and Blade Bluntness

Cutting quality decreases or requires more effort: change the blade.

Contacting Service Support

If problems persist, contact the service team via website or email.

Accessories

Recommended Accessories List

Lists recommended accessories like blades, cutting sticks, blade changing tool, and stand.

Technical Data

Approvals and Certifications

Machine approved by safety labs, certified under ISO 9001/14001, specs on machine sticker, original label required for guarantee.

Company Certifications Details

Details company certifications for quality, environmental, and energy management systems.

Related product manuals