IDEATEC DLC4000 - Key B2 and negative input 2 configuration (continued)

IDEATEC S.A. - Z.I. de Noville-les-Bois - rue Léopold Génicot 19A - 5380 Fernelmont, Belgium - Tel: +32(0)81 42 00 10 - Fax: +32(0)81 57 91 70 - E-mail: info@ideatec.be
User’s guide DLC4000/DLC8000 - Doc. V2.1 - Firmware V3.1
Page 18
Identification des éléments
Description des éléments
Description du produit
11.
&
5
7
8
3X8X
6
3X
6X
7X
5X
B5
B6
B3
B7
B8
B2 B4
B1
B5
B6
B3
B7
B8
B2 B4
B1
B5
B6
B3
B7
B8
B2 B4
B1
B5
B6
B3
B7
B8
B2 B4
B1
B5
B6
B3
B7
B8
B2 B4
B1
IN 2 -
4sec.
B5
B6
B3
B7
B8
B2 B4
B1
B5
B6
B3
B7
B8
B2 B4
B1
B5
B6
B3
B7
B8
B2 B4
B1
B5
B6
B3
B7
B8
B2 B4
B1
B5
B6
B3
B7
B8
B2 B4
B1
B5
B6
B3
B7
B8
B2 B4
B1
IN 2 -
IN 2 -
B5
B6
B3
B7
B8
B2 B4
B1
B5
B6
B3
B7
B8
B2 B4
B1
IN 2 -
4sec.
B5
B6
B3
B7
B8
B2 B4
B1
B5
B6
B3
B7
B8
B2 B4
B1
IN 2 -
4sec.
B5
B6
B3
B7
B8
B2 B4
B1
11.5. DLC4000/DLC8000 Configuration - MODE 1 (continued)
Operation & Configuration (continued)
10.5.2. Key B2 and negative input 2 configuration (continued)
SELECTION FLASHES DESCRIPTION
Key B2 is a switch in Salve mode (siren) and controls the positive output 2 / negative
output 1.
Key 2 is conditioned by the negative input 2 (siren status). When the siren is activated,
she send back a negative signal to confirm that all is working perfectly. If this signal
disappears then after 4 seconds key B2 is going OFF automatically.
Siren can be started again but only by pressing key B2.
Key B2 is a switch controlling positive output 2 / negative output 1 and is conditioned by
the key B1 (Master key, blue light). Key B2 working is conditioned by the negative input2
(handbrake signal). If the signal is present on negative input 2 the key B2 is disabled
and cannot be activated until the signal is still present.
Key B2 is not automatically activated if the signal on negative input 2 disapears.
Key B2 is a switch controlling positive output 2 / negative output 1 and is conditioned by
the key B1 (Master key, blue light). Key B2 is not conditioned by the negative input 2.
Key B2 is a switch controlling positive output 2 / negative output 1 and is conditioned by
the key B1 (Master key, blue light). Key 2 is also conditioned by the negative input 2
(siren status). When the siren is activated, she send back a negative signal to confirm
that all is working perfectly. If this signal disappears then after 4 seconds key B2 is going
OFF automatically. Siren can be started again but only by pressing key B2.