22
- Take out and fi ll the tank with 1 litre of water (up to the MAX
level).
- Introduce the descaling product supplied with the machine
into the tank full of water; wait for it to dissolve.
- Remove the capsule and capsule holder.
1 Liter
- Place an empty container with a capacity of at least 1 litre
beneath the brew head.
- Turn the steam wand toward the container; water will fl ow
out both from the brew head and the steam wand.
- Press the
button.
The
button and the icon in the circle will fl ash si-
multaneously to signal the beginning of the descaling cycle,
which lasts about 30 minutes.
- At the end of the cycle the machine will emit a beep The
button and the icon in the circle will start fl ashing
together with the other signals already present.
At this point it is necessary to clean the internal water circuit of
the machine of any residues of the descaling agent.
That is, the machine must be run through a rinse cycle; carry
out the following steps:
- Remove the tank and clean it thoroughly; fi ll it with 1 litre of
fresh water (up to the MAX level).
1 Liter
- Place an empty container with a capacity of at least 1 litre
beneath the brew head.
- Turn the steam wand toward the container; water will fl ow
out both from the brew head and the steam wand.
- Press the
button.
The
button and the icon in the circle will fl ash si-
multaneously to signal the beginning of the cycle for rinsing
the internal water circuit of the machine.
- At the end of the rinse cycle all the fl ashing signals will go off
and a beep will be emitted.
- Remove the water collection container from beneath the
brew head and wash it thoroughly.
- Refi ll the water tank again.
- Now the machine is ready for use.
WARNING:
- Should a mains power failure occur during the descaling
procedure, it will be necessary to repeat the cycle from
the start.
- If descaling is not performed as needed, scale build-up
may cause malfunctioning not covered by the warranty.
It is advisable to use the descaling agent supplied with
the machine.
- Do not use vinegar, lye, salt or formic acid because they
may damage the machine.
22
- Take out and fi ll the tank with 1 litre of water (up to the MAX
level).
- Introduce the descaling product supplied with the machine
into the tank full of water; wait for it to dissolve.
- Remove the capsule and capsule holder.
1 Liter
- Place an empty container with a capacity of at least 1 litre
beneath the brew head.
- Turn the steam wand toward the container; water will fl ow
out both from the brew head and the steam wand.
- Press the
button.
The
button and the icon in the circle will fl ash si-
multaneously to signal the beginning of the descaling cycle,
which lasts about 30 minutes.
- At the end of the cycle the machine will emit a beep The
button and the icon in the circle will start fl ashing
together with the other signals already present.
At this point it is necessary to clean the internal water circuit of
the machine of any residues of the descaling agent.
That is, the machine must be run through a rinse cycle; carry
out the following steps:
- Remove the tank and clean it thoroughly; fi ll it with 1 litre of
fresh water (up to the MAX level).
1 Liter
- Place an empty container with a capacity of at least 1 litre
beneath the brew head.
- Turn the steam wand toward the container; water will fl ow
out both from the brew head and the steam wand.
- Press the
button.
The
button and the icon in the circle will fl ash si-
multaneously to signal the beginning of the cycle for rinsing
the internal water circuit of the machine.
- At the end of the rinse cycle all the fl ashing signals will go off
and a beep will be emitted.
- Remove the water collection container from beneath the
brew head and wash it thoroughly.
- Refi ll the water tank again.
- Now the machine is ready for use.
WARNING:
- Should a mains power failure occur during the descaling
procedure, it will be necessary to repeat the cycle from
the start.
- If descaling is not performed as needed, scale build-up
may cause malfunctioning not covered by the warranty.
It is advisable to use the descaling agent supplied with
the machine.
- Do not use vinegar, lye, salt or formic acid because they
may damage the machine.
22
- Take out and fi ll the tank with 1 litre of water (up to the MAX
level).
- Introduce the descaling product supplied with the machine
into the tank full of water; wait for it to dissolve.
- Remove the capsule and capsule holder.
1 Liter
- Place an empty container with a capacity of at least 1 litre
beneath the brew head.
- Turn the steam wand toward the container; water will fl ow
out both from the brew head and the steam wand.
- Press the
button.
The
button and the icon in the circle will fl ash si-
multaneously to signal the beginning of the descaling cycle,
which lasts about 30 minutes.
- At the end of the cycle the machine will emit a beep The
button and the icon in the circle will start fl ashing
together with the other signals already present.
At this point it is necessary to clean the internal water circuit of
the machine of any residues of the descaling agent.
That is, the machine must be run through a rinse cycle; carry
out the following steps:
- Remove the tank and clean it thoroughly; fi ll it with 1 litre of
fresh water (up to the MAX level).
1 Liter
- Place an empty container with a capacity of at least 1 litre
beneath the brew head.
- Turn the steam wand toward the container; water will fl ow
out both from the brew head and the steam wand.
- Press the
button.
The
button and the icon in the circle will fl ash si-
multaneously to signal the beginning of the cycle for rinsing
the internal water circuit of the machine.
- At the end of the rinse cycle all the fl ashing signals will go off
and a beep will be emitted.
- Remove the water collection container from beneath the
brew head and wash it thoroughly.
- Refi ll the water tank again.
- Now the machine is ready for use.
WARNING:
- Should a mains power failure occur during the descaling
procedure, it will be necessary to repeat the cycle from
the start.
- If descaling is not performed as needed, scale build-up
may cause malfunctioning not covered by the warranty.
It is advisable to use the descaling agent supplied with
the machine.
- Do not use vinegar, lye, salt or formic acid because they
may damage the machine.
To Next Page
Loading...
Need help?
General
