EasyManuals Logo

InFocus Work Big IN15 User Manual

InFocus Work Big IN15
24 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #18 background imageLoading...
Page #18 background image
Troubleshooting
18
POWER
TEMP
LAMP
: Green steady
:–
:–
Zoom and focus cannot be performed due to some trouble in
the optical drive circuit. Turn off the projector and then turn it
back on again.
If the error occurs again when you turn power back on,
contact InFocus service at www.infocus.com/service
Press the [ESC] key to clear the warning message.
Message : Zoom and focus
cannot be performed
for some reason. Try
turning the projector
off and then back on
again.
If this message
reappears, request
servicing.
POWER
TEMP
LAMP
: Amber flashing
Red steady
: Red steady
:–
The projector was turned off automatically due to some
problem that was probably caused by external digital noise or
some other reason. Confirm that the POWER/STANDBY
indicator is lit red (without flashing) and that the fan has
stopped. After checking the POWER/STANDBY indicator,
disconnect the power cord from the projector and wait for all
of the projector’s indicators to go out. Next, reconnect the
power cord and turn projector power back on.
If the error occurs again when you turn power back on,
contact InFocus service at www.infocus.com/service
Message :
POWER
TEMP
LAMP
: Amber flashing
Red steady
: Red flashing
(0.5-second interval)
: Red flashing
(0.5-second interval)
The projector was turned off automatically because the lamp
turned off or did not turn on. After confirming that the
POWER/STANDBY indicator is lit red (without flashing), unplug
the power cord. Wait for a short while and then plug it back
in and turn on the projector again.
If the error occurs again when you turn power back on, wait
until the projector cools down and then replace the lamp
(lamp replacement instructions are in the section "Replacing
the Lamp" in the Reference Guide on the CD-ROM that
comes with the projector).
If the lamp does not light after you replace it, contact InFocus
service at www.infocus.com/service
Message :
POWER
TEMP
LAMP
: Amber flashing
Red steady
: Red flashing
(2-second interval)
:–
Power has turned off automatically due to a projector memory
error. Confirm that the POWER/STANDBY indicator is lit red
(without flashing) and that the fan has stopped. After checking
the POWER/STANDBY indicator, disconnect the power cord
from the projector and wait for all of the projector’s indicators
to go out. Next, reconnect the power cord and turn projector
power back on.
If the error occurs again when you turn power back on,
contact InFocus service at www.infocus.com/service
Message :
POWER
TEMP
LAMP
: Amber flashing
Red steady
: Amber flashing
(1-second interval)
:–
Power has turned off automatically because the lamp cover is
open. Perform the following steps.
After confirming that the POWER/STANDBY indicator is lit
red (without flashing), disconnect the power cord from the
projector.
Check to make sure that the lamp cover is closed.
Plug the power cord back in and turn the projector back
on again.
If the error occurs again when you turn power back on,
contact InFocus service at www.infocus.com/service
Message :
Indicator/Error Message Description and Required Action
Infocus IN15_UG_E.book Page 18 Tuesday, October 23, 2007 5:37 PM

Other manuals for InFocus Work Big IN15

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the InFocus Work Big IN15 and is the answer not in the manual?

InFocus Work Big IN15 Specifications

General IconGeneral
BrandInFocus
ModelWork Big IN15
CategoryProjector
LanguageEnglish

Related product manuals