EasyManua.ls Logo

Ingersoll-Rand 3000 - User Manual

Ingersoll-Rand 3000
24 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
22607402
Revision D
May 2015
Save These Instructions
Two-Stage Reciprocating Air Compressors
Models 2340, 2475, 2545, 7100, 15T & 3000
Owner’s Manual
Manual del usuario
ES
Manuel de l’utilisateur
FR
Owner’s Manual
EN

Table of Contents

Questions and Answers

  • M
    moorebrettAug 8, 2025
    What to do if the timer will not activate on my Ingersoll-Rand 3000 Air Compressor?
    • B
      Brett CarsonAug 8, 2025
      If the timer on your Ingersoll-Rand Air Compressor won't activate, several factors could be at play. First, ensure the unit is receiving power by checking the electrical supply. If power is present, the timer itself may be faulty and require replacement. Other potential issues include a clogged port, which necessitates cleaning the valve, a malfunctioning solenoid valve that needs replacing, or a clogged strainer, which should be cleaned.
  • R
    Robert JohnsonAug 16, 2025
    Why will the valve not close on my Ingersoll-Rand 3000 Air Compressor?
    • J
      jonesgwendolynAug 16, 2025
      The valve may not close due to debris in the solenoid valve preventing the diaphragm from seating properly. To resolve this, remove the solenoid valve, disassemble it, clean all components, and then reassemble it. Another possible cause is a short in an electrical component. Inspect the power cord or timer and replace them as needed.
  • K
    Kevin GuzmanAug 22, 2025
    What to do if valve will not close on Ingersoll-Rand 3000?
    • K
      Kathryn GrahamAug 22, 2025
      If the valve on your Ingersoll-Rand Air Compressor won't close, it could be due to debris in the solenoid valve preventing the diaphragm from seating. To fix this, remove the solenoid valve, disassemble it, clean it thoroughly, and then reassemble it. Another potential cause is a short in an electrical component. Inspect the power cord or timer and replace them if necessary.
  • J
    joann96Aug 30, 2025
    Why is the timer not activating on my Ingersoll-Rand 3000 Air Compressor?
    • L
      Lauren WilsonAug 31, 2025
      If the timer on your Ingersoll-Rand Air Compressor isn't activating, several factors could be at play. First, ensure there is an electrical supply reaching the timer. If there is no power, apply it. If power is present, the timer itself might be malfunctioning and need replacement. Other potential issues include a clogged port, which requires cleaning the valve, a malfunctioning solenoid valve needing replacement, or a clogged strainer that needs cleaning.

Summary

General Information

Introduction

Provides instructions for installation, operation, and maintenance of the compressor.

Warranty & Product Registration

Application

Two-Stage Operation

Explanation of Safety Signal Words

Receipt & Inspection

General Safety Rules

Selecting a Location

Electric Motor Compressors

Guidelines for choosing an indoor location for electric motor compressors.

Gasoline Engine Compressors

Guidelines for choosing an indoor location for gasoline engine compressors.

Ambient Temperature Considerations

Recommendations for operating temperatures and potential issues.

Mounting

Concrete Floors (Electric Motor or Gasoline Engine Powered Compressors)

Procedure for mounting compressors on concrete floors.

Truck Beds (Gasoline Engine Powered Compressors Only)

Air Discharge Connections

Air Inlet Connections

Electrical Connections

Permanently Connected Electric Compressors

Electrical installation and service requirements for permanently connected units.

Condensate Discharge Piping

Pressure Switch Wiring (For Compressors Not Requiring a Starter)

IEC Power Connection and Overload Adjustment

Gasoline Engine Compressors Electrical

Compressor Lubrication

Recommended Lubricant

Specifies the recommended lubricant for Ingersoll Rand compressors.

Operation

Daily Pre-Operation Checks

Daily checks to perform before operating the compressor.

Start-Up (Electric Motor Driven Compressors)

Step-by-step guide for starting electric motor driven compressors.

Pressure Switch Adjustment

Adjustment Procedures (Adjustable Switches)

Step-by-step guide for adjusting pressure switches.

Pilot Valve Adjustment

Oil Consumption Check

Compressor Controls (Gasoline Engine Compressors)

Constant Speed Control

Details on constant speed control for gasoline engines.

Maintenance

Maintenance Schedule

Schedule of recommended maintenance tasks and intervals.

Belt Adjustment

Tensioning Belts

Procedures for adjusting belt tension on various models.

Electric Drain Maintenance

Tank Inspection

Troubleshooting

Electric Drain Troubleshooting

Troubleshooting common issues with electric drain valves.

Diagrams & Tables

Fastener Torque Table

Table listing torque specifications for various fasteners.

Electrical Wiring Diagrams

Single Phase Wiring

Wiring diagram for single-phase electric motor compressors.

Three Phase Wiring

Wiring diagram for three-phase electric motor compressors.

Typical Baseplate Unit

Typical Horizontal Simplex Unit

Typical Vertical Simplex Unit

Typical Gasoline Engine Unit

Warranty

Limitation of Liability

Legal terms regarding liability limitations for the equipment.

Ingersoll-Rand 3000 Specifications

General IconGeneral
Horsepower3 hp
Max Pressure175 psi
Maximum Pressure175 psi
Drive TypeBelt Drive
Tank Size80 gal
Voltage208-230/460 V
Phase1/3
Air Delivery11.3 CFM @ 90 psi

Related product manuals