Ingersoll-Rand R160 Product Maintenance Information

32 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

80447212

Revision D

April 2015

Save These Instructions

Contact-Cooled Rotary Screw Air Compressor

Product Maintenance Information

R30, R37, R45, R55, R75, R90, R110, R132, R160

42915.12.22

PRINT LANGUAGE

ENGLISH

CHINESE

Table of Contents

Other manuals for Ingersoll-Rand R160

Manual276 pages

Product Information48 pages

Questions and Answers:

V
Victoria JenkinsAug 27, 2025
What to do if Ingersoll-Rand R160 Air Compressor is stopped and will not restart?
- J
  Jennifer EvansAug 27, 2025
  If your Ingersoll-Rand Air Compressor is stopped and won't restart, it could be due to the following reasons: * The controller has tripped the compressor and hasn't been reset. See Tables 4 and 5. * The emergency stop button has been pressed but not released. Identify the reason, repair the fault, disengage the button, and reset the controller. * The emergency stop button has been pressed and released, but the controller hasn't been reset. Repair the fault and reset the controller.
L
lanerobertAug 27, 2025
Why does my Ingersoll-Rand R160 stop and not restart?
- E
  Eric WeberAug 27, 2025
  If your Ingersoll-Rand Air Compressor stops and will not restart, it could be due to: * A tripped drive controller. See Tables 4 and 5. * The controller has tripped the compressor. See Tables 4 and 5. * The maximum number of starts per hour has been exceeded.
J
Julian KingAug 28, 2025
Why is the discharge air from my Ingersoll-Rand R160 too hot?
- V
  Vincent MillerAug 28, 2025
  If the discharge air from your Ingersoll-Rand Air Compressor is too hot, consider these potential causes: * High ambient temperature. Review the installation and system parameters. * Insufficient cooling air. Check the ducting and cooling air path, and verify the direction of blower rotation. * Dirty or blocked aftercooler (cooling air side). Clean or replace the aftercooler.
P
Peter SmithAug 29, 2025
Why is my Ingersoll-Rand Air Compressor package producing excessive noise?
- C
  Cheryl LopezAug 29, 2025
  Excessive noise from your Ingersoll-Rand Air Compressor package can be due to several reasons: * Ensure all panels and doors are properly closed. * Check for air leaks from internal pipework or components; repair or replace as necessary. * Inspect the blower or blower motor bearings for wear; repair or replace if needed. * Remove any loose debris impacting the blower during rotation and repair any damage. * Check if the blowdown valve is stuck open; repair or replace it. * Verify that the pressure relief valve is seating correctly; repair or replace it if not. * Look for vibration due to motor, airend, or blower imbalance; repair or replace the affected components.
J
Jasmine ScottSep 13, 2025
What causes remote start failure in Ingersoll-Rand Air Compressor?
- N
  Nicholas AdamsSep 14, 2025
  If you are experiencing remote start failure with your Ingersoll-Rand Air Compressor: * The remote start button may be pressed after the compressor is already running, or the remote start button remains closed. Check the operation of the buttons or operating procedures.
T
Thomas TuckerSep 12, 2025
Why do I need to check setpoints on Ingersoll-Rand Air Compressor?
- R
  Ryan ShepherdSep 12, 2025
  You may need to check the setpoints on your Ingersoll-Rand Air Compressor if: * The controller software has been changed. Recalibrate all sensors and check the setpoints.
C
Charles PatrickSep 12, 2025
What to do if sensor failure occurs in Ingersoll-Rand Air Compressor?
- J
  Jennifer MossSep 12, 2025
  If a sensor failure occurs in your Ingersoll-Rand Air Compressor: * The sensor may be missing or faulty. Install, repair, or replace the faulty sensor.
K
kennedyzacharySep 5, 2025
What causes excessive coolant consumption in Ingersoll-Rand Air Compressor?
- D
  David HodgesSep 5, 2025
  Excessive coolant consumption in your Ingersoll-Rand Air Compressor can be due to: * A coolant system leak. Repair or replace the leaking components. * See also ‘discharge air is contaminated with coolant’.
M
Michael AllenSep 3, 2025
Why is pressure too high in Ingersoll-Rand Air Compressor because speed is not reducing?
- G
  georgeshafferSep 3, 2025
  If the pressure produced by your Ingersoll-Rand Air Compressor is too high because the speed isn't reducing as demand decreases: * The controller settings may be incorrect. Check and modify the settings. * The pressure transducer may be faulty, incorrectly calibrated, or not receiving a pressure signal. Recalibrate or replace it.
M
Mr. Gary MartinezSep 4, 2025
What causes condensate contamination in Ingersoll-Rand Air Compressor discharge air?
- B
  Brittany AdamsSep 4, 2025
  If the discharge air from your Ingersoll-Rand Air Compressor is contaminated with condensate: * The aftercooler may not be functioning correctly. Clean or replace it. * The moisture separator drain trap may be faulty. Repair or replace it.

Ingersoll-Rand R160 Specifications

General

Brand	Ingersoll-Rand
Model	R160
Category	Air Compressor
Language	English

Related product manuals

Ingersoll-Rand R132

Ingersoll-Rand R75

Preview: Ingersoll-Rand R30

Ingersoll-Rand R30

Ingersoll-Rand R45

Ingersoll-Rand R90

Ingersoll-Rand R37

Ingersoll-Rand RS22i

Ingersoll-Rand RS22n

Ingersoll-Rand RS15n

Preview: Ingersoll-Rand RS30i

Ingersoll-Rand RS30i

Preview: Ingersoll-Rand RS15ie

Ingersoll-Rand RS15ie

Preview: Ingersoll-Rand R4-11 kW

Ingersoll-Rand R4-11 kW