Ingersoll-Rand R45 Product Maintenance Information

32 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

80447212

Revision D

April 2015

Save These Instructions

Contact-Cooled Rotary Screw Air Compressor

Product Maintenance Information

R30, R37, R45, R55, R75, R90, R110, R132, R160

42915.12.22

PRINT LANGUAGE

ENGLISH

CHINESE

Table of Contents

Other manuals for Ingersoll-Rand R45

Manual276 pages

Product Information48 pages

Questions and Answers:

D
Debbie ButlerAug 23, 2025
How to troubleshoot Ingersoll-Rand R45 Air Compressor that will not start?
- M
  Morgan WilliamsAug 23, 2025
  If your Ingersoll-Rand Air Compressor will not start, it could be due to several reasons: * There may be no power supply. Ensure the power is switched on. If it is, contact a qualified electrician. * There may be a controller failure. Check the supply to the controller and replace it if necessary. * There may be a starter failure. Isolate the supply, lock it off, tag it, and replace the failed component. Alternatively, contact your local Ingersoll Rand representative.
T
Teresa GreenSep 3, 2025
Why is pressure too high in Ingersoll-Rand Air Compressor because speed is not reducing?
- S
  Sherri FloresSep 3, 2025
  If the pressure produced by your Ingersoll-Rand Air Compressor is too high because the speed isn't reducing as demand decreases: * The controller settings may be incorrect. Check and modify the settings. * The pressure transducer may be faulty, incorrectly calibrated, or not receiving a pressure signal. Recalibrate or replace it.
L
Lawrence HayesSep 2, 2025
What to do if discharge air is contaminated with coolant in Ingersoll-Rand Air Compressor?
- V
  Virginia SmithSep 2, 2025
  If the discharge air from your Ingersoll-Rand Air Compressor is contaminated with coolant: * Check if the scavenge pipe is blocked or broken, or if the o-ring is not sealing. Clean or replace as necessary. * Inspect the separator element for punctures, incorrect installation, the need for replacement, or incorrect sealing. Replace if needed. * If incorrect coolant has been added, drain the system, check for damage, clean, and refill with the correct coolant. * If the system has been overfilled with coolant, check for damage and drain the excess.
L
Laura AcevedoSep 1, 2025
What causes high airend discharge temperature in Ingersoll-Rand Air Compressor?
- S
  Sarah RaySep 1, 2025
  High airend discharge temperature in your Ingersoll-Rand Air Compressor can be caused by: * Compressor operating above rated pressure: Check and modify settings. Review system requirements. * Low coolant level: Check for leaks and top up coolant. See also information about discharge air being contaminated with coolant. * High ambient temperature: Review installation and system parameters. * Insufficient cooling air: Check ducting and cooling air path. * Dirty, blocked coolant cooler (cooling air side): Clean or replace.
R
Richard LaneAug 31, 2025
What causes Ingersoll-Rand Air Compressor discharge air to be too hot?
- B
  Brent HawkinsAug 31, 2025
  If the discharge air from your Ingersoll-Rand Air Compressor is too hot, it could be due to: * High ambient temperature: Review the installation and system parameters. * Insufficient cooling air: Check the ducting and cooling air path, and verify the direction of blower rotation. * Dirty, blocked aftercooler (cooling air side): Clean or replace it.
K
Kelly MillerAug 30, 2025
Why does my Ingersoll-Rand Air Compressor package draw too much current?
- W
  William JohnsonAug 30, 2025
  If your Ingersoll-Rand Air Compressor package is drawing too much current, consider these potential causes: * The compressor may be operating above its rated pressure. Check and adjust the settings accordingly. * A separator filter element might be dirty or blocked. Replace it.
R
Roy BernardAug 29, 2025
Why is my Ingersoll-Rand Air Compressor package producing excessive noise?
- M
  Michael WernerAug 29, 2025
  Excessive noise from your Ingersoll-Rand Air Compressor package can be due to several reasons: * Ensure all panels and doors are properly closed. * Check for air leaks from internal pipework or components; repair or replace as necessary. * Inspect the blower or blower motor bearings for wear; repair or replace if needed. * Remove any loose debris impacting the blower during rotation and repair any damage. * Check if the blowdown valve is stuck open; repair or replace it. * Verify that the pressure relief valve is seating correctly; repair or replace it if not. * Look for vibration due to motor, airend, or blower imbalance; repair or replace the affected components.
M
Mary HernandezAug 28, 2025
Why is the discharge air from my Ingersoll-Rand R45 too hot?
- M
  Ms. Alexis RamirezAug 28, 2025
  If the discharge air from your Ingersoll-Rand Air Compressor is too hot, consider these potential causes: * High ambient temperature. Review the installation and system parameters. * Insufficient cooling air. Check the ducting and cooling air path, and verify the direction of blower rotation. * Dirty or blocked aftercooler (cooling air side). Clean or replace the aftercooler.
J
Jennifer MasseyAug 27, 2025
Why does my Ingersoll-Rand Air Compressor stop and not restart?
- E
  Emma SmithAug 27, 2025
  If your Ingersoll-Rand Air Compressor stops and will not restart, it could be due to: * A tripped drive controller. See Tables 4 and 5. * The controller has tripped the compressor. See Tables 4 and 5. * The maximum number of starts per hour has been exceeded.
S
Susan WilliamsAug 26, 2025
What to do if Ingersoll-Rand R45 Air Compressor is stopped and will not restart?
- R
  Richard HillAug 26, 2025
  If your Ingersoll-Rand Air Compressor is stopped and won't restart, it could be due to the following reasons: * The controller has tripped the compressor and hasn't been reset. See Tables 4 and 5. * The emergency stop button has been pressed but not released. Identify the reason, repair the fault, disengage the button, and reset the controller. * The emergency stop button has been pressed and released, but the controller hasn't been reset. Repair the fault and reset the controller.

Ingersoll-Rand R45 Specifications

General

Brand	Ingersoll-Rand
Model	R45
Category	Air Compressor
Language	English

Related product manuals

Preview: Ingersoll-Rand R4-11 kW

Ingersoll-Rand R4-11 kW

Ingersoll-Rand R75

Preview: Ingersoll-Rand R30

Ingersoll-Rand R30

Ingersoll-Rand R37

Ingersoll-Rand R55

Ingersoll-Rand R160

Ingersoll-Rand RS22i

Ingersoll-Rand RS55i

Preview: Ingersoll-Rand RS45i

Ingersoll-Rand RS45i

Ingersoll-Rand RS15n

Preview: Ingersoll-Rand RS30i

Ingersoll-Rand RS30i

Ingersoll-Rand RS22ne