Ingersoll-Rand Sierra H 200 User Manual

72 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

SL, SM & SH 90, 110, 132, 150, 200, 250 & 300 (50Hz)

L, H & HH 125, 150, 200, 250, 300, 350 & 400 (60Hz)

This manual contains

important safety information

and must be made available

to personnel who operate and

maintain this machine.

OPERATION AND MAINTENANCE MANUAL

LIBRO D’USO E MANUTENZIONE

MANUAL DE MANEJO Y MANTENIMIENTO

MANUAL DE OPERAÇAO E CONSERVAÇAO

C.C.N. : 80441306

REV. : D

DATE : JANUARY 2010

en pt it es

ENGLISH

PRINT LANGUAGE

PORTUGUESE

SPANISH

ITALIAN

Table of Contents

Questions and Answers:

M
michael96Aug 25, 2025
What causes a Ingersoll-Rand Sierra H 200 Air Compressor to fail to load?
- A
  angelawilliamsonAug 25, 2025
  If your Ingersoll-Rand Air Compressor fails to load, start by checking for leaking seals in the hydraulic cylinder. If the cylinder doesn't fully stroke when the 'Load' button is pressed, overhaul the hydraulic cylinder. Also, check for a defective load solenoid valve by removing the tube that runs from the load solenoid valve to the hydraulic cylinder. Start the compressor and press the 'Load' button; if oil doesn't come out of the solenoid valve, replace it.
C
Charles MartinAug 28, 2025
How to get rid of water in Ingersoll-Rand Sierra H 200 Air Compressor system?
- D
  Dennis WhitakerAug 28, 2025
  If you find water in your Ingersoll-Rand Air Compressor system, start by inspecting the moisture separator/drain trap for defects and clean if required; replace if defective. Check the trap drain and drain piping for any blockages and clean them. Inspect and clean the aftercooler core if it's dirty. Ensure all enclosure panels are in place. If the unit lacks an aftercooler, consider installing one. Finally, ensure the drain line/drip leg is correctly installed, sloping the drain line away from the trap and installing a drip leg.
D
Daniel Freeman Jr.Aug 31, 2025
Why is my Ingersoll-Rand Air Compressor making so much noise?
- A
  Alicia Blackburn DDSAug 31, 2025
  If your Ingersoll-Rand Air Compressor has an excessive noise level, inspect and tighten any loose component mountings. Ensure that all enclosure panels are in place. If the compressor itself is defective, contact an authorized distributor immediately and do not operate the unit.
J
Joshua DunnSep 4, 2025
What to do with excessive vibration of Ingersoll-Rand Sierra H 200?
- S
  Samantha ReynoldsSep 4, 2025
  If your Ingersoll-Rand Air Compressor is experiencing excessive vibration, inspect and tighten any loose components. If the motor or compressor bearing has failed, contact an authorized distributor immediately and do not operate the unit. Inspect the area for other equipment that may be causing external vibrations.
K
Kimberly ParsonsSep 7, 2025
Why does the pressure relief valve keep opening on my Ingersoll-Rand Sierra H 200?
- B
  brownmeganSep 8, 2025
  If the pressure relief valve on your Ingersoll-Rand Air Compressor opens, it could be due to the compressor operating over pressure; adjust the controller set points. Alternatively, the valve itself may be defective and require replacement.

Ingersoll-Rand Sierra H 200 Specifications

General

Model	Sierra H 200
Drive Type	Direct Drive
Type	Rotary Screw
Power	200 HP
Voltage	460 V / 3 / 60 Hz

Summary

SAFETY

General Information

General safety guidelines, precautions for operation, and maintenance.

Compressed air

Electrical

Critical safety precautions for electrical systems and servicing.

INSTALLATION / HANDLING

LOCATION IN THE PLANT

Guidelines for optimal compressor placement and environmental conditions.

COMMISSIONING

Critical checks and procedures required before initial machine startup.

DISCHARGE PIPING

OPERATING INSTRUCTIONS

EMERGENCY STOP SWITCH (1)

Function and reset procedure for the emergency stop button.

PUSH BUTTONS

CURRENT STATUS

OPERATOR SETPOINTS

How to adjust user-configurable operating parameters.

SENSOR CALIBRATION

Procedure for calibrating critical machine sensors for accuracy.

ALARM HISTORY

WARNING

How warning messages are displayed and what they signify.

ALARMS

How alarm messages are displayed and what they signify.

PRIOR TO STARTING

Final checks and safety procedures before powering on the unit.

MAINTENANCE

ROUTINE MAINTENANCE

Overview of periodic maintenance tasks and recommended intervals.

AIR FILTER CHANGE PROCEDURE

OIL AND OIL FILTER

Procedures for changing the oil and the oil filter element.

TROUBLE SHOOTING

Compressor fails to start.

Common causes and remedies for issues preventing compressor startup.

Compressor shuts down.

Diagnosis and solutions for unexpected compressor shutdowns.

Low system air pressure.

Troubleshooting steps for addressing low air output or pressure.

Compressor fails to load.

Water in system.

Pressure relief valve opens.

Related product manuals

Ingersoll-Rand Sierra H 250

Ingersoll-Rand Sierra H 60

Ingersoll-Rand Sierra H 50

Ingersoll-Rand Sierra H 75

Ingersoll-Rand Sierra H 125

Ingersoll-Rand Sierra H 150

Ingersoll-Rand Sierra H 300

Ingersoll-Rand Sierra H 350

Ingersoll-Rand Sierra H 400

Ingersoll-Rand Sierra SH 200

Ingersoll-Rand Sierra HH 200

Ingersoll-Rand Sierra SL 200