What to do if InSinkErator Water Dispenser water is too hot or not hot enough?
If the water from your InSinkErator Water Dispenser is too hot or not hot enough, the thermostat may not be adjusted to your needs. Adjust the thermostat slowly, then depress or twist the tap handle for 20 seconds to bring in fresh water to be heated at the new setting. Allow 5-7 minutes for the water to reach the new temperature.
Why is water not hot in my InSinkErator Water Dispenser?
The InSinkErator Water Dispenser may not be heating because it is not properly plugged into a functioning, earthed electrical outlet. Check that the circuit breaker or fuses are working and that the outlet is switched on.
Why is InSinkErator F-H3300C LED green light not on?
If the green LED light on the front of your InSinkErator Water Dispenser tank is not illuminated, the unit may not be plugged in, or the electrical outlet may be inoperative. Make sure that the circuit breaker or fuses are functioning properly and that the outlet is not switched off.
What to do if InSinkErator F-H3300C water comes out of vent instead of spout?
If water is coming out of the vent instead of the spout on your InSinkErator Water Dispenser, the outlet tube may be blocked. Check that the outlet tube is not kinked, twisted, or pinched. Also, unscrew the spout end piece and clean out any debris.
Why is InSinkErator Water Dispenser water dripping from the spout/vent constantly?
Constant dripping from the spout or vent of your InSinkErator Water Dispenser indicates debris in the water line, which may be in the tap valve seat, causing a slow leak. Try unscrewing the spout end piece and cleaning out any debris. Then, depress or twist the lever 7-10 times to flush the tap and lines.
What to do if InSinkErator Water Dispenser water is dripping from the spout/vent intermittently?
If your InSinkErator Water Dispenser is dripping intermittently from the spout or vent, it could be due to the expansion chamber not draining properly because of low water pressure, or the spout is blocked. Unplug the unit. If the dripping doesn't stop after a few minutes, check the supply valve to ensure it is fully open and that there are no obstructions in the water line reducing the pressure below 172 kPa (1.7 bar; 25 psi), such as a poorly mounted saddle valve, a clogged water filter, or a partially opened shut-off valve. Also, unscrew the spout end piece and clean out any debris.
Why InSinkErator Water Dispenser has divided stream?
A divided stream from your InSinkErator Water Dispenser is caused by debris in the end piece. Unscrew the spout end piece and clean out any debris.
Why InSinkErator F-H3300C Water Dispenser water has discoloration/rusty appearance?
Water discoloration or a rusty appearance in your InSinkErator Water Dispenser indicates corrosion of the unit. Unplug and drain the unit. If the water discoloration remains after draining and refilling the unit, discontinue use and contact an authorized InSinkErator service agent.
Important notes for installation, usage, and safety, especially for Australia and New Zealand.
List of tools and equipment necessary for installation.
Additional items needed for installation, such as drill bits and anchors.
Steps to prepare the installation area, including checking clearances and electrical outlets.
Step-by-step guide for installing the HC1100 and GN1100 hot water taps.
How to adjust the water temperature setting on the tank unit.
Instructions for unplugging, draining, and storing the unit during periods of non-use or freezing temperatures.
Guidelines for cleaning the tap and tank components using mild cleaners.
Common problems related to the water filter and their solutions.
General| Brand | InSinkErator |
|---|---|
| Model | F-H3300C |
| Finish | Chrome |
| Height | 14.5 inches |
| Voltage | 120V |
| Power | 750W |
| Type | Water Dispenser |
| Material | Stainless Steel |
| Safety Features | Child Safety Lock |
To Next Page