What to do if InSinkErator F-HC1100C Water Dispenser water is too hot or not hot enough?
If the water from your InSinkErator Water Dispenser is too hot or not hot enough, the thermostat may not be adjusted to your needs. Adjust the thermostat slowly, then depress or twist the tap handle for 20 seconds to bring in fresh water to be heated at the new setting. Allow 5-7 minutes for the water to reach the new temperature.
Why is water not hot in my InSinkErator F-HC1100C Water Dispenser?
The InSinkErator Water Dispenser may not be heating because it is not properly plugged into a functioning, earthed electrical outlet. Check that the circuit breaker or fuses are working and that the outlet is switched on.
Why is InSinkErator F-HC1100C Water Dispenser LED green light not on?
If the green LED light on the front of your InSinkErator Water Dispenser tank is not illuminated, the unit may not be plugged in, or the electrical outlet may be inoperative. Make sure that the circuit breaker or fuses are functioning properly and that the outlet is not switched off.
What to do if InSinkErator F-HC1100C Water Dispenser water comes out of vent instead of spout?
If water is coming out of the vent instead of the spout on your InSinkErator Water Dispenser, the outlet tube may be blocked. Check that the outlet tube is not kinked, twisted, or pinched. Also, unscrew the spout end piece and clean out any debris.
Why is InSinkErator F-HC1100C water dripping from the spout/vent constantly?
Constant dripping from the spout or vent of your InSinkErator Water Dispenser indicates debris in the water line, which may be in the tap valve seat, causing a slow leak. Try unscrewing the spout end piece and cleaning out any debris. Then, depress or twist the lever 7-10 times to flush the tap and lines.
What to do if InSinkErator F-HC1100C water is dripping from the spout/vent intermittently?
If your InSinkErator Water Dispenser is dripping intermittently from the spout or vent, it could be due to the expansion chamber not draining properly because of low water pressure, or the spout is blocked. Unplug the unit. If the dripping doesn't stop after a few minutes, check the supply valve to ensure it is fully open and that there are no obstructions in the water line reducing the pressure below 172 kPa (1.7 bar; 25 psi), such as a poorly mounted saddle valve, a clogged water filter, or a partially opened shut-off valve. Also, unscrew the spout end piece and clean out any debris.
Why InSinkErator F-HC1100C Water Dispenser has divided stream?
A divided stream from your InSinkErator Water Dispenser is caused by debris in the end piece. Unscrew the spout end piece and clean out any debris.
Why InSinkErator F-HC1100C Water Dispenser water has discoloration/rusty appearance?
Water discoloration or a rusty appearance in your InSinkErator Water Dispenser indicates corrosion of the unit. Unplug and drain the unit. If the water discoloration remains after draining and refilling the unit, discontinue use and contact an authorized InSinkErator service agent.
Essential safety, regulatory, and general knowledge for installation.
Lists required tools, optional items, and components included in the product package.
Steps to prepare before starting the installation process.
Detailed instructions for installing the HC1100/GN1100 model tap.
Instructions on how to connect the tap's water lines to the tank.
Connects the system to the main water supply.
Procedures for filling the tank and connecting the electrical power.
How to set the desired water temperature for the tap.
Instructions for storing the unit during periods of non-use or freezing temperatures.
Guidance on cleaning the tap and its components.
Information on filter maintenance and replacement procedures.
Specific troubleshooting steps for problems related to the water filter.
General| Brand | InSinkErator |
|---|---|
| Model | F-HC1100C |
| Category | Water Dispenser |
| Language | English |
To Next Page