EasyManua.ls Logo

InSinkErator SWT-FLTR-1 - User Manual

InSinkErator SWT-FLTR-1
80 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Installation Manual
English
Manual de instalación
Español
Manuel d’installation
Français
Installationshandbuch
Deutsch
Installatiehandleiding
Nederlands
Manual de Instalação
Português
Руководство по установке
Русский
Installationsvejledning
Dansk
Manuale di installazione
Italiano
Instrukcja instalacji
Polski
치 매
한국
2
8
14
20
26
32
38
44
50
56
62
68
F-HC3300C
F-HC3300BR
F-H3300C
F-H3300BR
F-HC1100C
F-HC1100BR
F-GN1100C
F-GN1100BR
SWT-FLTR-1,
-2, -3, -4
SWT-3, -7
steaming
hot water
tap
ltered 98°C
water on tap
安装手
中文
74

Questions and Answers

  • S
    Shane FritzAug 12, 2025
    What to do if InSinkErator Water Dispenser water is too hot or not hot enough?
    • M
      Michele NunezAug 12, 2025
      If the water from your InSinkErator Water Dispenser is too hot or not hot enough, the thermostat may not be adjusted to your needs. Adjust the thermostat slowly, then depress or twist the tap handle for 20 seconds to bring in fresh water to be heated at the new setting. Allow 5-7 minutes for the water to reach the new temperature.
  • M
    Mason KimAug 16, 2025
    Why is water not hot in my InSinkErator Water Dispenser?
    • B
      Brenda SampsonAug 16, 2025
      The InSinkErator Water Dispenser may not be heating because it is not properly plugged into a functioning, earthed electrical outlet. Check that the circuit breaker or fuses are working and that the outlet is switched on.
  • W
    Walter BlackAug 20, 2025
    Why is InSinkErator SWT-FLTR-1 LED green light not on?
    • J
      Joseph KramerAug 20, 2025
      If the green LED light on the front of your InSinkErator Water Dispenser tank is not illuminated, the unit may not be plugged in, or the electrical outlet may be inoperative. Make sure that the circuit breaker or fuses are functioning properly and that the outlet is not switched off.
  • P
    Patricia GrayAug 23, 2025
    What to do if InSinkErator SWT-FLTR-1 water comes out of vent instead of spout?
    • D
      Danielle LongAug 25, 2025
      If water is coming out of the vent instead of the spout on your InSinkErator Water Dispenser, the outlet tube may be blocked. Check that the outlet tube is not kinked, twisted, or pinched. Also, unscrew the spout end piece and clean out any debris.
  • P
    Patrick FlynnAug 27, 2025
    Why is InSinkErator SWT-FLTR-1 Water Dispenser water dripping from the spout/vent constantly?
    • D
      donna46Aug 27, 2025
      Constant dripping from the spout or vent of your InSinkErator Water Dispenser indicates debris in the water line, which may be in the tap valve seat, causing a slow leak. Try unscrewing the spout end piece and cleaning out any debris. Then, depress or twist the lever 7-10 times to flush the tap and lines.
  • T
    Timothy RandolphAug 31, 2025
    What to do if InSinkErator SWT-FLTR-1 water is dripping from the spout/vent intermittently?
    • D
      Dr. Natalie Bryan DVMAug 31, 2025
      If your InSinkErator Water Dispenser is dripping intermittently from the spout or vent, it could be due to the expansion chamber not draining properly because of low water pressure, or the spout is blocked. Unplug the unit. If the dripping doesn't stop after a few minutes, check the supply valve to ensure it is fully open and that there are no obstructions in the water line reducing the pressure below 172 kPa (1.7 bar; 25 psi), such as a poorly mounted saddle valve, a clogged water filter, or a partially opened shut-off valve. Also, unscrew the spout end piece and clean out any debris.
  • S
    Sherri MitchellSep 3, 2025
    Why InSinkErator SWT-FLTR-1 Water Dispenser has divided stream?
    • M
      Michael LaneSep 3, 2025
      A divided stream from your InSinkErator Water Dispenser is caused by debris in the end piece. Unscrew the spout end piece and clean out any debris.
  • S
    stephenpowersSep 7, 2025
    Why InSinkErator SWT-FLTR-1 water has discoloration/rusty appearance?
    • K
      Kyle NortonSep 7, 2025
      Water discoloration or a rusty appearance in your InSinkErator Water Dispenser indicates corrosion of the unit. Unplug and drain the unit. If the water discoloration remains after draining and refilling the unit, discontinue use and contact an authorized InSinkErator service agent.

Summary

Pre-Installation Information

What You Should Know Before You Begin

Essential safety and general information before starting installation.

Additional Considerations

Specific regional requirements and important user advice.

In This Package

Lists all included components for installation.

Installation Guide

How to Use This Instruction Manual

Explains the manual's structure and how to follow instructions.

Start Here: Proper Installation

Overview and initial steps for installation, including time estimate.

Preparation and Tap Installation

Covers preparation and installing the HC1100/GN1100 tap.

Install HC3300;H3300, Mount Tank, Connect Lines

Steps for installing HC3300/H3300 tap, mounting tank, and connecting tap to tank.

Filtration, Final Connection, and Power Up

Covers filter installation, final water connection, and powering the unit.

Operating Instructions

Using the Hot Water Tap

Detailed instructions on how to use the hot water tap.

Care and Maintenance

Adjusting the Thermostat

How to set and adjust the water temperature.

Seasonal Storage and Drainage

Procedures for storing the unit during periods of non-use or freezing.

Cleaning the Tap and Tank

Guidance on cleaning the tap and tank components.

Filter Guide and Replacement

Information on filter maintenance and replacement procedures.

Troubleshooting

Problem Diagnosis and Solutions

Common issues, their causes, and recommended solutions.

InSinkErator SWT-FLTR-1 Specifications

General IconGeneral
Filter Life6 months
Filter TypeCarbon Block
ModelSWT-FLTR-1
Flow Rate0.75 gpm
CompatibilityInSinkErator instant hot water dispensers
Micron Rating0.5 microns
ReducesChlorine taste and odor

Related product manuals