EasyManua.ls Logo

InSinkErator SWT-FLTR-2 - User Manual

InSinkErator SWT-FLTR-2
80 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Installation Manual
English
Manual de instalación
Español
Manuel d’installation
Français
Installationshandbuch
Deutsch
Installatiehandleiding
Nederlands
Manual de Instalação
Português
Руководство по установке
Русский
Installationsvejledning
Dansk
Manuale di installazione
Italiano
Instrukcja instalacji
Polski
치 매
한국
2
8
14
20
26
32
38
44
50
56
62
68
F-HC3300C
F-HC3300BR
F-H3300C
F-H3300BR
F-HC1100C
F-HC1100BR
F-GN1100C
F-GN1100BR
SWT-FLTR-1,
-2, -3, -4
SWT-3, -7
steaming
hot water
tap
ltered 98°C
water on tap
安装手
中文
74

Questions and Answers

  • D
    Daniel WebbAug 13, 2025
    What to do if InSinkErator SWT-FLTR-2 water is too hot or not hot enough?
    • S
      Samantha MeadowsAug 13, 2025
      If the water from your InSinkErator Water Dispenser is too hot or not hot enough, the thermostat may not be adjusted to your needs. Adjust the thermostat slowly, then depress or twist the tap handle for 20 seconds to bring in fresh water to be heated at the new setting. Allow 5-7 minutes for the water to reach the new temperature.
  • T
    Thomas AcostaAug 16, 2025
    Why is water not hot in my InSinkErator SWT-FLTR-2?
    • P
      pmartinezAug 17, 2025
      The InSinkErator Water Dispenser may not be heating because it is not properly plugged into a functioning, earthed electrical outlet. Check that the circuit breaker or fuses are working and that the outlet is switched on.
  • M
    morgan45Aug 20, 2025
    Why is InSinkErator SWT-FLTR-2 LED green light not on?
    • C
      Charles MartinezAug 20, 2025
      If the green LED light on the front of your InSinkErator Water Dispenser tank is not illuminated, the unit may not be plugged in, or the electrical outlet may be inoperative. Make sure that the circuit breaker or fuses are functioning properly and that the outlet is not switched off.
  • L
    Lori MillerAug 25, 2025
    What to do if InSinkErator Water Dispenser water comes out of vent instead of spout?
    • M
      Mrs. Ashley DiazAug 25, 2025
      If water is coming out of the vent instead of the spout on your InSinkErator Water Dispenser, the outlet tube may be blocked. Check that the outlet tube is not kinked, twisted, or pinched. Also, unscrew the spout end piece and clean out any debris.
  • K
    karenstephensAug 28, 2025
    Why is InSinkErator SWT-FLTR-2 Water Dispenser water dripping from the spout/vent constantly?
    • M
      Mr. Mark ArnoldAug 28, 2025
      Constant dripping from the spout or vent of your InSinkErator Water Dispenser indicates debris in the water line, which may be in the tap valve seat, causing a slow leak. Try unscrewing the spout end piece and cleaning out any debris. Then, depress or twist the lever 7-10 times to flush the tap and lines.
  • K
    Kyle FergusonAug 31, 2025
    What to do if InSinkErator Water Dispenser water is dripping from the spout/vent intermittently?
    • D
      Diane SmithAug 31, 2025
      If your InSinkErator Water Dispenser is dripping intermittently from the spout or vent, it could be due to the expansion chamber not draining properly because of low water pressure, or the spout is blocked. Unplug the unit. If the dripping doesn't stop after a few minutes, check the supply valve to ensure it is fully open and that there are no obstructions in the water line reducing the pressure below 172 kPa (1.7 bar; 25 psi), such as a poorly mounted saddle valve, a clogged water filter, or a partially opened shut-off valve. Also, unscrew the spout end piece and clean out any debris.
  • M
    Michael McculloughSep 4, 2025
    Why InSinkErator SWT-FLTR-2 has divided stream?
    • W
      woodmatthewSep 4, 2025
      A divided stream from your InSinkErator Water Dispenser is caused by debris in the end piece. Unscrew the spout end piece and clean out any debris.
  • A
    Anthony NelsonSep 8, 2025
    Why InSinkErator SWT-FLTR-2 water has discoloration/rusty appearance?
    • A
      Albert NguyenSep 8, 2025
      Water discoloration or a rusty appearance in your InSinkErator Water Dispenser indicates corrosion of the unit. Unplug and drain the unit. If the water discoloration remains after draining and refilling the unit, discontinue use and contact an authorized InSinkErator service agent.

Summary

Getting Started & Preparation

Before You Begin: Key Information

Essential safety, operational, and additional considerations before installation.

Required Equipment & Package Contents

List of necessary tools, equipment, and items included in the package.

Installation Guide

Using This Instruction Manual

Guidance on navigating and utilizing the instruction manual effectively.

Installation Preparation & Overview

Initial checks, preparations, and a view of the completed setup.

Installing the Tap (HC1100;GN1100)

Step-by-step guide for installing the HC1100 and GN1100 tap models.

Installing the Tap (HC3300;H3300)

Mounting the Tank

Procedures for securely attaching the water tank under the sink.

Connecting Tap to Tank

Instructions for connecting the tap's water lines to the tank.

Filtration & Water Connection

Installing Filtration

Steps for installing the water filter system.

Fill Tank & Connect Power

Procedures for filling the tank and connecting the power supply.

Care, Use & Troubleshooting

Maintenance Procedures

Covers thermostat adjustment, storage, cleaning, and filter replacement.

General Troubleshooting

Common problems and their solutions for the steaming hot water tap.

Warranty Information

Troubleshooting: Filtration Issues

InSinkErator SWT-FLTR-2 Specifications

General IconGeneral
TypeWater Filtration System
ModelSWT-FLTR-2
CompatibilityInSinkErator Instant Hot Water Tanks
Filter TypeCarbon Block
Filter Life6 months
Filtration Capacity500 gallons
Filter Life (Gallons)500 gallons
ReducesChlorine taste and odor, particulates
NSF CertificationNSF/ANSI Standard 42

Related product manuals