EasyManuals Logo

Integra DRX-3.2 User Manual

Integra DRX-3.2
163 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #124 background imageLoading...
Page #124 background image
124
Front Panel Rear Panel Remote
Contents
Connections
Playback
Setup
Setting Item Default Value Setting Details
Bluetooth Wakeup O󰀨
This function wakes up the unit on standby by
connecting a BLUETOOTH-enabled device.
"On": When this function is used
"O󰀨": When this function is not used
When this is set to "On", power consumption
increases in standby mode, however, the
increase in power consumption is minimized by
automatically entering the Hybrid Standby mode
where only the essential circuits are operating.
This setting is xed to "O󰀨" if "Bluetooth" - "Auto
Input Change" is set to "O󰀨".
Wait for a while if "Network Standby" and "Bluetooth Wakeup" cannot be selected. It can
be selected when the network function is activated.
5. 12V Trigger A
Set when outputting the control signal (maximum 12 V/100 mA) through the 12V
TRIGGER OUT A jack. Di󰀨erent settings can be set for each input selector. You
can enable power link operation when you connect the unit and the external
devices equipped with 12V trigger input jack.
Setting Item Default Value Setting Details
Delay 0 sec Set after how many seconds the 12V trigger output
will occur in response to the unit's operation. As
some devices cause a large current when they turn
on, delay the output if such devices are connected.
Select a value between "0 sec" to "3 sec".
Setting Item Default Value Setting Details
BD/DVD Main Set the 12V trigger output setting to each input.
"O󰀨": No output
"Main": Output when "BD/DVD" is selected as input
for main room.
"Zone 2": Output when "BD/DVD" is selected as
input for ZONE2.
"Main/Zone 2": Output when "BD/DVD" is selected
as input for main room or ZONE2.
"Zone 3": Output when "BD/DVD" is selected as
input for ZONE3.
"Main/Zone 3": Output when "BD/DVD" is selected
as input for main room or ZONE3.
"Zone 2/Zone 3": Output when "BD/DVD" is
selected as input for ZONE2 or ZONE3.
"Main/Zone 2/Zone 3": Output when "BD/DVD"
is selected as input for main room, ZONE2 or
ZONE3.
CBL/SAT Main Set the 12V trigger output setting to each input.
"O󰀨": No output
"Main": Output when "CBL/SAT" is selected as
input for main room.
"Zone 2": Output when "CBL/SAT" is selected as
input for ZONE2.
"Main/Zone 2": Output when "CBL/SAT" is selected
as input for main room or ZONE2.
"Zone 3": Output when "CBL/SAT" is selected as
input for ZONE3.
"Main/Zone 3": Output when "CBL/SAT" is selected
as input for main room or ZONE3.
"Zone 2/Zone 3": Output when "CBL/SAT" is
selected as input for ZONE2 or ZONE3.
"Main/Zone 2/Zone 3": Output when "CBL/SAT"
is selected as input for main room, ZONE2 or
ZONE3.

Table of Contents

Other manuals for Integra DRX-3.2

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Integra DRX-3.2 and is the answer not in the manual?

Integra DRX-3.2 Specifications

General IconGeneral
BrandIntegra
ModelDRX-3.2
CategoryStereo Receiver
LanguageEnglish

Related product manuals