www.intermatic.com
Pool & Spa Controls
P4043ME
PE140
P4243ME
Actuator Controller
& Load Mechanisms
P4000ME Series
Actuator Control & Load Mechanisms
Specifications:
UÊ£Óä]ÊÓän]ÊÓ{äÊ6Ê«ÕÌÊÛÌ>}i
UÊÌÀÃÊÕ«ÊÌÊÌÀiiÊÛ>ÛiÊ>VÌÕ>ÌÀÃ
UÊ-ÜÌViÃÊi>ÌiÀÊÌiÀÃÌ>Ì
UÊ,iÌiÊVÌÀÊV>«>LÌiÃ
UÊ}iVÞÊ>««ÀÛ>\Ê-É1-
UÊÌÀÃÊÌÜÊVÀVÕÌÃÊ(P4243ME only)
Contact Ratings – Each Circuit
UÊ6>ÛiÊVÌÕ>ÌÀÊ-Õ««Þ\ÊÓ{Ê6]Ê{äÊ6
UÊ£ÇÊ«Ê,iÃÃÌÛi]Ê£ÓäÓ{äÊ6]ÊxäÉÈäÊâÊ(P4243ME only)
UÊÊ£°xÊ*]Ê£ÓäÊ6]ÊxäÉÈäÊâÊ(P4243ME only)
UÊÊΰäÊ*]ÊÓ{äÊ6]ÊxäÉÈäÊâÊ(P4243ME only)
UÊÊ£äÊ«Ê/Õ}ÃÌi]Ê£Óä]ÊÓ{äÊ6]ÊxäÉÈäÊâÊ(P4243ME only)
P4043ME – Valve Actuator Control Mechanism
Have you ever wanted an affordable control that would only automate a set of water
Û>ÛiÃÊvÀÊÌiÊ«Ê«ÃÌÊÌÊÌiÊë>Ê«Ã̶Ê"ÀÊ>ÞLiÊÕÃÌÊÌÕÀÊ>ÊÃ}iÊÜ>ÌiÀÊ
valve to engage a water feature?
Designed specifically for aftermarket and retro-fit applications, the P4043ME is ideal
for controlling up to three water valve actuators with any latching or momentary
contactor (not provided) capable of providing 120 VAC or 240 VAC. In addition, the
P4043ME can switch the thermostat on most heaters between pool and spa when the
actuators change position.
The P4043ME is ideal for those applications where only simple water valve control
ÃÊÀiµÕÀi`Ê>`ÊV>ÊLiÊÌÀ}}iÀi`ÊLÞÊ>ÞÊÃÜÌV}Ê`iÛViÊÞÕÊ>ÞÊ«ÀÛ`iÊ°i°Ê}ÌÊ
switch, spring wound AUTO/OFF, wireless switch, relay, etc…). Installation is easy!
Simply snap the P4043ME into any existing Intermatic enclosure that contains an
available mechanism support bracket, hook up power to both the P4043ME and the
trigger device, and plug in your 24 VAC water valve actuators behind the top door of
the mechanism.
PE140 – Valve Actuator Control
If you do not have an Intermatic enclosure, you can order the PE140 model which
contains the P4043ME mechanism and the appropriate low voltage hardware for
running your actuator cables.
P4243ME – Valve/Pump Switch Mechanism
Designed as part of the I-Wave system and for aftermarket and retro-fit applications,
the P4243ME does everything a P4043ME does and is most suited for controlling
up to two different circuits associated with pool/spa combinations. It can also
LiÊÕÃi`ÊÌÊVÌÀÊ>ÊÌiÊiµÕ«iÌÊÌÞ«V>ÞÊii`i`ÊÊViVÌÊÜÌÊÜ>ÌiÀÊ
features, solar heating and other similar applications. This unit snaps into almost any
Intermatic enclosure and controls pumps up to 3HP, 24 volt supply for up to three
valve actuators, automatic HIGH/LOW water temperature selector, heater connection
circuit and push button control for each load with indicator lights on the face of
switch. In addition, the unit has connections for a hard wired or wireless remote and a
master switch controller.
Note: The following page refers to only a fraction of the most common applications of
the MultiWave Control System. Contact your Intermatic sales representative or
visit www.intermatic.com and visit the Pool & Spa section of our website for more
application ideas and details.
TITLE
20
COMPLIANT
118
http://waterheatertimer.org/Digital-control-centers-and-manuals.html#actuator
To Next Page
Need help?
General
