EasyManua.ls Logo

Intex 128366NP - User Manual

Intex 128366NP
86 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Zusammengeführte PDF Datei. Die Originale sind im folgenden Verzeichnis verlinkt. / Merged PDF File. Original files are linked in the following list. / Sloučený soubor PDF.
Originály jsou propojeny v následujícím adresáři. / Egyesített PDF fájl. Az eredetiek a következő könyvtárban találhatók. / Zlúčený súbor PDF. Originály sú prepojené v
nasledujúcom adresári. / Združena datoteka PDF. Izvirniki so povezani v naslednjem imeniku. / Spojena PDF datoteka. Izvornici su povezani u sljedećem imeniku.
128366NP - Frame Pool Set Ultra Quadra 732 x 366 x
132 cm
Above Ground Pool 2
097IO 17
052IO 33
261IO 35
165IO 69
Overview Pool Size vs Pump Running Time 81
Air Valve For Water Revitalization Set 83
Skimmer/Vakkuumreinigungsset Montageanleitung 84
Mounting 86

Table of Contents

Questions and Answers

  • L
    Lauren MillerSep 8, 2025
    What to do if Intex Swimming Pool filter motor fails to start?
    • C
      carpentertoddSep 8, 2025
      First, ensure the power cord is securely plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. If the RCD circuit breaker has tripped, reset it. If it repeatedly trips, your electrical system may have a defect, so turn off the breaker and consult an electrician. The motor may also be too hot, in which case you should let it cool down before restarting. Finally, check if the system is in stand-by/power saving mode.
  • S
    scottchristineAug 23, 2025
    What to do if my Intex 128366NP doesn’t work?
    • L
      Laura BrewerAug 23, 2025
      If the pump isn't working, first check that the water level is correct. Then, clean the strainer screens at the pool inlet. Also, inspect the intake hose for air leaks and tighten the hose nuts, checking for any damage.
  • K
    Kevin MooreSep 5, 2025
    Why are there white flakes in my Intex Swimming Pool water?
    • J
      John SmithSep 5, 2025
      If there are white flakes in the water of your Intex Swimming Pool, drain about 20 to 25% of the pool water and add fresh water to decrease the calcium hardness. Inspect the electrolytic cell for scale buildup, and clean the electrolytic cell if necessary.
  • I
    Ian RiceSep 3, 2025
    How to fix Intex 128366NP pressure gauge that doesn't work?
    • X
      xsimmonsSep 4, 2025
      If the pressure gauge on your Intex Swimming Pool Pump doesn’t work, clear any obstructions in the intake by unscrewing it from the 6-way valve.
  • F
    Felicia ReynoldsSep 2, 2025
    Why is sand flowing back into my Intex Swimming Pool?
    • S
      Stephanie HarrisSep 2, 2025
      If sand is flowing back into your Intex Swimming Pool, use only No. 20 silica sand with a particle size range of 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75. If the sand bed is calcified, change the sand.
  • S
    stephaniesimpsonSep 1, 2025
    How to stop Intex 128366NP hose from leaking?
    • J
      John NunezSep 1, 2025
      If the hose of your Intex Swimming Pool Pump is leaking, tighten or reinstall the hose nut. Also, ensure the o-ring or L-shape o-ring is in place and not damaged at the hose connection fitting.
  • C
    carlaperezAug 30, 2025
    What to do if Intex Swimming Pool inlet threaded air connector or air jet valve is leaking?
    • T
      Theresa BuchananAug 30, 2025
      If the inlet threaded air connector or air jet valve of your Intex Swimming Pool is leaking, tighten or reinstall the plunger valve. Tighten the air jet valve and make sure it’s facing up. If the air jet valve internal seal is locked, turn the pump ON and run for few seconds, then turn OFF, repeat 3 times. Remove the air jet valve, flush dirt out with water and replace the valve back if the air jet valve internal seal is dirty.
  • A
    Alexander GarciaAug 29, 2025
    How to fix Intex 128366NP Swimming Pool Pump 6-way valve or cover leaking?
    • T
      Thomas HartAug 29, 2025
      If the 6-way valve or cover of your Intex Swimming Pool Pump is leaking, remove the 6-way valve cover and ensure the o-ring is in place. Clean the sand tank o-ring with garden hose water if it's dirty. Tighten the flange clamp with the wrench supplied.
  • A
    Amy SmithAug 27, 2025
    What to do if my Intex Swimming Pool Pump filter doesn't clean the pool?
    • A
      anthony32Aug 27, 2025
      If your Intex Swimming Pool Pump isn't cleaning the pool effectively, ensure proper chlorine and pH levels by consulting your local swimming pool supply store. If there is no filtering media in the tank, load it with filter sand. Make sure the 6-way valve is set to the “FILTER” position. For an excessively dirty pool, operate the filter for longer periods. Clean the basket if there is dirt or sand on the pool floor.
  • A
    Ashley OdonnellAug 26, 2025
    How to fix Intex 128366NP filter motor that fails to start?
    • R
      Ryan WalkerAug 27, 2025
      If the filter motor of your Intex Swimming Pool Pump fails to start, ensure the power cord is securely plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. If the RCD circuit breaker has tripped, reset it. If it trips repeatedly, there may be an electrical defect requiring an electrician. If the motor is too hot, let it cool down before restarting.

Intex 128366NP Specifications

General IconGeneral
BrandIntex
Model128366NP
CategorySwimming Pool Pump
LanguageEnglish

Related product manuals