How to troubleshoot Intex 28647EG filter motor that fails to start?
If the Intex Swimming Pool Pump filter motor fails to start, ensure the line cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. Also, reset the GFCI/RCD circuit breaker; if it trips repeatedly, there may be an electrical system defect requiring an electrician. If the motor is too hot, let it cool down before restarting.
What to do if my Intex 28647EG doesn’t work?
If your Intex Swimming Pool Pump isn’t working, make sure the water level is correct. Clean the strainer screens at the pool inlet if they are clogged. If there is an air leak on the intake hose, tighten the hose nuts and check the hose for damage. If the motor is faulty or the impeller is jammed, contact an Intex service center.
How to fix a leaking 6-way valve/cover on Intex 28647EG?
If the Intex Swimming Pool Pump's 6-way valve or cover is leaking, remove the 6-way valve cover and make sure the o-ring is in place. Clean the sand tank o-ring with garden hose water if it's dirty. Tighten the flange clamp securely. If the 6-way valve is damaged, contact an Intex service center.
Why is my Intex Swimming Pool Pump hose leaking and how to fix it?
If the hose on your Intex Swimming Pool Pump is leaking, first tighten or reinstall the hose nut securely. Then, make sure the o-ring or L-shape o-ring is in place at the hose connection fitting and is not damaged.
Why is sand flowing back into my Intex Swimming Pool and how to stop it?
If sand is flowing back into the pool from your Intex Swimming Pool Pump, use only No. 20 silica sand with a particle size range of 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75. If the sand bed is calcified, change the sand.
How to fix a leaking inlet threaded air connector/air jet valve on Intex Swimming Pool Pump?
If the inlet threaded air connector or air jet valve on your Intex Swimming Pool Pump is leaking, tighten or reinstall the plunger valve. Ensure the air jet valve is tight and facing up. If the air jet valve internal seal is blocked, turn the pump ON for a few seconds, then turn it OFF, and repeat 3 times. If the air jet valve internal seal is dirty, remove the air jet valve, flush dirt out with water, and replace the valve back. If the air jet valve is broken, replace it with a new one.
What to do if the timer is inaccurate or can't be set on Intex Swimming Pool Pump?
If the timer on your Intex Swimming Pool Pump is inaccurate or cannot be set, turn off the pump and restart it 5 minutes later. Also, try re-setting the timer. If problems persist, contact an Intex service center.
What to do if the pressure gauge doesn’t work on Intex Swimming Pool Pump?
If the pressure gauge on your Intex Swimming Pool Pump doesn’t work, clear any obstructions in the intake by unscrewing it from the 6-way valve. If the pressure gauge is damaged, contact an Intex service center.
What to do if my Intex 28647EG Swimming Pool Pump doesn't pump water or flow is very slow?
If your Intex Swimming Pool Pump doesn't pump water or the flow is very slow, first check for any clogs in the inlet or discharge and clear any obstructions. Then, look for air leaks on the intake line and tighten hose nuts, inspect hoses for damage, and verify the pool water level. Clean the pre-filtering basket more often if the pool is excessively dirty. Backwash the filter if the sand media is clogged with dirt. Ensure the nozzle is at the upper position of the pool inlet and the strainer at the lower position of the pool outlet. If there's crusting on the filtering sand surface, remove about 1 inch of sand if necessary. Also, remove any pool vacuuming device attached to the system line. Finally, ensure the inlet threaded air connector is connected to the pool inlet upper hole.
How to improve cleaning performance of Intex 28647EG filter?
If the Intex Swimming Pool Pump filter isn't cleaning the pool, adjust the chlorine and pH levels. Load the tank with filter sand according to the sand loading instructions. Ensure the 6-way valve is set to the “FILTER” position. If the pool is excessively dirty, operate the filter for longer periods. Clean the strainer screen at the inlet if it's restricting water flow.
Instructions for correctly filling the sand filter tank with the specified sand media.
Detailed steps for installing the 6-way valve onto the sand filter tank and connecting hoses.
Steps for the initial startup of the pump, including backwashing and setting operating modes.
Guide to operating the pump using the timer mode or in manual (continuous) mode.
A guide to identify and resolve common issues with the sand filter pump's operation.
General| Model | 28647EG |
|---|---|
| Type | Sand Filter Pump |
| Voltage | 110-120V |
| Frequency | 60 Hz |
| Inlet/Outlet Size | 1.5 inches |
| Cord Length | 25 feet |
To Next Page