EasyManua.ls Logo

Intex 26647EG - User Manual

Intex 26647EG
24 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
342
PO
(342PO) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/08/2018
English
Model SF80110-2
Model SF70110-2
Model SF60110-2
Don’t forget to try these other fine Intex products: pools, pool
accessories, inflatable pools and in-home toys, airbeds and boats
available at fine retailers or visit our website.
Due to a policy of continuous product improvement, Intex
reserves the right to change specifications and appearance, which
may result in updates to the instruction manual without notice.
OWNER’S MANUAL
For illustrative purposes only.
IMPORTANT!
DO NOT RETURN PRODUCT TO STORE
To purchase parts and accessories or to obtain non-technical assistance, visit
www.intexcorp.com
For technical assistance and missing parts call us toll-free (for U.S. and Canadian Residents):
1-800-234-6839
Monday through Friday, 8:30am to 5:00pm Pacific Time
342-*PO-R0-1906
IMPORTANT
SAFETY RULES
Read, understand, and follow
all instructions carefully before
installing and using this product.

Table of Contents

Questions and Answers

  • A
    Angela WhiteAug 16, 2025
    How to troubleshoot Intex 26647EG Swimming Pool Pump filter motor that fails to start?
    • L
      Leon SchneiderAug 16, 2025
      If the Intex Swimming Pool Pump filter motor fails to start, ensure the line cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. Also, reset the GFCI/RCD circuit breaker; if it trips repeatedly, there may be an electrical system defect requiring an electrician. If the motor is too hot, let it cool down before restarting.
  • P
    Pamela AtkinsAug 18, 2025
    What to do if my Intex 26647EG doesn’t work?
    • C
      Courtney PonceAug 18, 2025
      If your Intex Swimming Pool Pump isn’t working, make sure the water level is correct. Clean the strainer screens at the pool inlet if they are clogged. If there is an air leak on the intake hose, tighten the hose nuts and check the hose for damage. If the motor is faulty or the impeller is jammed, contact an Intex service center.
  • P
    paulajonesAug 21, 2025
    How to fix a leaking 6-way valve/cover on Intex 26647EG Swimming Pool Pump?
    • J
      jordandavisAug 21, 2025
      If the Intex Swimming Pool Pump's 6-way valve or cover is leaking, remove the 6-way valve cover and make sure the o-ring is in place. Clean the sand tank o-ring with garden hose water if it's dirty. Tighten the flange clamp securely. If the 6-way valve is damaged, contact an Intex service center.
  • S
    salinasanthonyAug 25, 2025
    Why is my Intex 26647EG Swimming Pool Pump hose leaking and how to fix it?
    • C
      campbellpamelaAug 25, 2025
      If the hose on your Intex Swimming Pool Pump is leaking, first tighten or reinstall the hose nut securely. Then, make sure the o-ring or L-shape o-ring is in place at the hose connection fitting and is not damaged.
  • R
    Renee WilliamsAug 28, 2025
    Why is sand flowing back into my Intex Swimming Pool and how to stop it?
    • A
      Andrew GilbertAug 28, 2025
      If sand is flowing back into the pool from your Intex Swimming Pool Pump, use only No. 20 silica sand with a particle size range of 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75. If the sand bed is calcified, change the sand.
  • A
    Alicia AustinAug 30, 2025
    How to fix a leaking inlet threaded air connector/air jet valve on Intex 26647EG?
    • A
      afloresAug 31, 2025
      If the inlet threaded air connector or air jet valve on your Intex Swimming Pool Pump is leaking, tighten or reinstall the plunger valve. Ensure the air jet valve is tight and facing up. If the air jet valve internal seal is blocked, turn the pump ON for a few seconds, then turn it OFF, and repeat 3 times. If the air jet valve internal seal is dirty, remove the air jet valve, flush dirt out with water, and replace the valve back. If the air jet valve is broken, replace it with a new one.
  • D
    Danielle SmithSep 2, 2025
    What to do if the timer is inaccurate or can't be set on Intex 26647EG?
    • K
      Krystal HallSep 2, 2025
      If the timer on your Intex Swimming Pool Pump is inaccurate or cannot be set, turn off the pump and restart it 5 minutes later. Also, try re-setting the timer. If problems persist, contact an Intex service center.
  • F
    Felicia MorenoSep 5, 2025
    What to do if the pressure gauge doesn’t work on Intex 26647EG Swimming Pool Pump?
    • S
      Sherri TuckerSep 5, 2025
      If the pressure gauge on your Intex Swimming Pool Pump doesn’t work, clear any obstructions in the intake by unscrewing it from the 6-way valve. If the pressure gauge is damaged, contact an Intex service center.
  • A
    aaguirreSep 8, 2025
    What to do if my Intex 26647EG Swimming Pool Pump doesn't pump water or flow is very slow?
    • D
      Douglas HicksSep 9, 2025
      If your Intex Swimming Pool Pump doesn't pump water or the flow is very slow, first check for any clogs in the inlet or discharge and clear any obstructions. Then, look for air leaks on the intake line and tighten hose nuts, inspect hoses for damage, and verify the pool water level. Clean the pre-filtering basket more often if the pool is excessively dirty. Backwash the filter if the sand media is clogged with dirt. Ensure the nozzle is at the upper position of the pool inlet and the strainer at the lower position of the pool outlet. If there's crusting on the filtering sand surface, remove about 1 inch of sand if necessary. Also, remove any pool vacuuming device attached to the system line. Finally, ensure the inlet threaded air connector is connected to the pool inlet upper hole.
  • C
    Catherine HubbardSep 12, 2025
    How to improve cleaning performance of Intex 26647EG filter?
    • S
      Sheryl GardnerSep 12, 2025
      If the Intex Swimming Pool Pump filter isn't cleaning the pool, adjust the chlorine and pH levels. Load the tank with filter sand according to the sand loading instructions. Ensure the 6-way valve is set to the “FILTER” position. If the pool is excessively dirty, operate the filter for longer periods. Clean the strainer screen at the inlet if it's restricting water flow.

Summary

Important Safety Rules

Read and Follow All Instructions

Emphasizes the necessity of reading and understanding all safety instructions before use.

Product Specifications

Setup Instructions

Sand Loading

Guides on how to properly fill the sand filter tank with the correct media.

6-Way Valve Installation

Sand Filter Pump Hose Connection Setup

Operating Instructions

6-Way Valve Positions and Function

Explains the different settings of the 6-way valve and their operational functions.

Control Panel Description

Initial Startup and Operation

Motor Pre-Filter Cleaning and Maintenance

Troubleshooting Guide

Intex 26647EG Specifications

General IconGeneral
BrandIntex
Model26647EG
CategorySwimming Pool Pump
LanguageEnglish

Related product manuals