Intex CS20220 User Manual

241A
SAVE THESE INSTRUCTIONS
(241IO) SALTWATER SYSTEM & SAND FILTER PUMP (14” & 16”) ENGLISH 7.5” X 10.3” PANTONE 295U 08/09/2013
English
Page 31
TROUBLESHOOTING GUIDE (continued)
INSUFFICIENT
CHLORINE
INSUFFICIENT
COPPER ION LEVEL
POOL IS STAINED
WHITE FLAKES IN
THE WATER
NO LED DISPLAY
GREEN HAIR
• Without cyanuric acid.
• Insufficient operating hours of the
Saltwater System.
• The salt level in the pool water
is less than 2000ppm. This is
insufficient.
• Chlorine loss due to intense
sunlight exposure.
• The bather load has increased.
• Clogged or dirty electrolytic cell.
• High UV level exposure.
• Insufficient operating hours.
• The PH is too high.
• The bather load has increased.
• Clogged or dirty electrolytic cell.
• Copper electrode defective.
• High copper ion concentration.
• Excessive calcium hardness is
present in pool water.
• No power supply.
• RCD/GFCI has not reseted.
• A power fuse has blown.
• LED failure.
• Incorrect switching, press two
buttons ( and ) together.
• High copper ion concentration.
• See “Cyanuric acid table”.
• Increase the daily Saltwater System operating
time. See “Operating Instructions”.
• Check the salt level with the Test Kit. Adjust as
needed. See “Salt & Pool Water Volumes”.
• Use a pool cover when the pool is not in use
and/or when the unit is operating.
• Increase the daily Saltwater System operating
time. See “Operating Instructions”.
• Remove the cell for inspection, clean it if
necessary. See “Maintenance”.
• Cover the pool with a pool cover for 2 days
with the device running and then test the water
using the test strips.
• If the pool is clean and clear, add stabilizer to
the water and then test the water with the
device running.
• Increase operating time per day. See
“Operating Instructions”.
• Use PH decrease chemical to adjust, contact
your local pool chemical store.
• Increase the operating time per day. See
“Operating Instructions”.
• Remove the cell for inspection, clean it if
necessary. See “Maintenance”.
• Contact Intex Service Center.
• Drain about 20% of the pool water and add
fresh water to decrease the copper ion
concentration below 0.2ppm.
• Add aluminum sulfate: 1000 liters water need
around 2g (1000 gals need 0.27 ounce) or
aluminum potassium sulfate: 1000 liters water
need around 3g (1000 gals need 0.4 ounce) to
pool.
• Use a lemon based cleaning product
(preferably containing citric acid). Don’t scrub
with aggressive cleaning products because this
might etch the underlying surface.
• Drain about 20 to 25% of the pool water and
add fresh water to decrease the calcium
hardness. Inspect the electrolytic cell for scale
buildup. Clean the electrolytic cell if necessary.
• Plug the cell cord firmly into the cell housing
receptacle.
• Reset the RCD/GFCI.
• Contact Intex Service Center.
• Contact Intex Service Center.
• Shut down and turn on the power again, re-set
the time. See “Operating Instructions”.
• Drain about 20% of the pool water and add
fresh water to decrease the copper ion
concentration below 0.2ppm.
• Add aluminum sulfate: 1000 liters water need
around 2g (1000 gals need 0.27 ounce) or
aluminum potassium sulfate: 1000 liters water
need around 3g (1000 gals need 0.4 ounce) to
pool.
• Use ‘Ultra-Swim’ shampoo, or shampoo
containing chelating agents.
PROBLEM CAUSE SOLUTION

Intex CS20220 Specifications

General

Brand	Intex
Model	CS20220
Category	Swimming Pool Pump
Language	English