To Next PageTo Next PageHow do I fix a leaking hose on my Intex Krystal Clear SX3200?
If the hose is leaking on your Intex Swimming Pool Pump, tighten or reinstall the hose nut. Also, ensure the o-ring or L-shape o-ring is in place and not damaged at the hose connection fitting.
What to do if my Intex Krystal Clear SX3200 Swimming Pool Pump doesn't work?
If the Intex Swimming Pool Pump doesn’t work, first ensure that the water level is correct. Next, clean the strainer screens at the pool inlet. Then, check for any air leaks on the intake hose and tighten the hose nuts, inspecting the hose for damage.
How to fix Intex Swimming Pool Pump filter motor that fails to start?
If the Intex Swimming Pool Pump filter motor fails to start, ensure it is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. Also, reset the GFCI/RCD circuit breaker; if it trips repeatedly, have an electrician check your electrical system. If the motor is too hot, let it cool down before restarting.
What to do if my Intex Krystal Clear SX3200 Swimming Pool Pump filter doesn't clean the pool?
If your Intex Swimming Pool Pump doesn't clean the pool, adjust the chlorine and pH levels, consulting your local swimming pool supply stores for guidance. Ensure the tank is loaded with filter sand according to the sand loading instructions. Set the 6-way valve to the “FILTER” position. If the pool is excessively dirty, operate the filter for longer periods. Also, clean the strainer screen at the inlet, if it’s restricting the water flow.
How to troubleshoot an inaccurate or non-setting timer on an Intex Krystal Clear SX3200 Swimming Pool Pump?
If the timer on your Intex Swimming Pool Pump is inaccurate or can't be set, turn off the pump and restart it after 5 minutes. Then, try resetting the timer again.
How to stop a 6-way valve/cover leak in my Intex Krystal Clear SX3200 Swimming Pool Pump?
If the 6-way valve or cover on your Intex Swimming Pool Pump is leaking, remove the 6-way valve cover and make sure the sand tank o-ring is in place. Clean the sand tank o-ring with garden hose water if it's dirty. Ensure the flange clamp is securely tightened.
Why is the timer on my Intex Swimming Pool inaccurate or can't be set?
If the timer is inaccurate or can't be set on your Intex Swimming Pool, turn off the pump and restart 5 minutes later. Reset the timer. If the issue persists, contact the Intex service center.
What to do about a small leak from the Intex Swimming Pool air jet valve when the pump is on?
If there is a small leak from the air jet valve when the pump is on for your Intex Swimming Pool, remove all accessories (such as solar mat, auto pool cleaner, LED light) from the water circulation line and place the air jet valve cap over the air jet valve. Do not cover the air jet valve with the valve cap under normal situations or when the pump is operating.
What to do if Intex Krystal Clear SX3200 doesn’t work?
If the Intex Swimming Pool pump isn’t working, ensure the pool is filled to the correct water level. Clean the strainer screens at the pool inlet. Tighten hose nuts and check the hose for damage to address any air leaks on the intake hose. For a faulty motor or jammed impeller, contact the Intex service center.
Why is the Intex Swimming Pool filter not pumping water or has very slow flow?
If your Intex Swimming Pool filter isn’t pumping water or the flow is very slow, start by clearing any obstructions in the intake hose by discharging it inside the pool wall. Check for air leaks on the intake line by tightening hose nuts and inspecting hoses for damage, also check pool water level. Clean the pre-filtering basket more often if the pool is excessively dirty. Backwash the filter if the sand media is clogged with dirt. Ensure the nozzle is at the upper position of the pool inlet and the strainer at the lower position of the pool outlet. Remove about 1” of sand if there's crusting or caking on the filtering sand surface. Remove any pool vacuuming device attached to the system line. Finally, ensure the inlet threaded air connector is connected to the pool inlet upper hole.
General| Model | SX3200 |
|---|---|
| Type | Sand Filter Pump |
| Voltage | 110-120V |
| Tank Diameter | 16 inches |
| Hose Size | 1.5 inches |
| Pump Flow Rate | 3, 200 GPH |
| Sand Capacity | 100 lbs |
| System Flow Rate | 2, 450 gph (9, 274 L/hr) |
