To Next PageTo Next PageWhat to do if Intex Krystal Clear SX925 Water Pump pressure gauge doesn’t work?
If the pressure gauge on your Intex Water Pump isn’t working, clear any obstructions in the intake by unscrewing it from the 4-way valve.
What to do if sand is flowing back into the pool from my Intex Water Pump?
If sand is flowing back into the pool, ensure you are using only No. 20 silica sand with a particle size range of 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75. If the sand bed is calcified, change the sand.
What to do if Intex Water Pump 4-way valve or cover leaking?
If the 4-way valve or cover on your Intex Water Pump is leaking, remove the 4-way valve cover and make sure the sand tank o-ring is in place and clean. If dirty, clean it with garden hose water. Also, ensure the flange clamp is securely tightened.
What to do if the Intex Krystal Clear SX925 timer is inaccurate or can't be set?
If the timer on your Intex Water Pump is inaccurate or can't be set, turn off the pump and restart it 5 minutes later. If that doesn't work, try re-setting the timer.
How to troubleshoot Intex Krystal Clear SX925 Water Pump filter motor that fails to start?
If the Intex Water Pump filter motor fails to start, ensure the line cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. If the GFCI/RCD circuit breaker has tripped, reset it. If it trips repeatedly, there may be an electrical system defect; turn off the circuit breaker and consult an electrician. Also, the motor may be too hot; allow it to cool down before restarting.
What to do if Intex Krystal Clear SX925 Water Pump filter doesn’t clean pool?
If the Intex Water Pump filter isn’t cleaning the pool, adjust the chlorine and pH levels, consulting local swimming pool supply stores if needed. Ensure the tank is loaded with filter sand according to the “sand loading instructions”. Set the 4-way valve to the “FILTER” position. If the pool is excessively dirty, operate the filter for longer periods. Also, clean the strainer screen at the inlet if it restricts water flow.
What to do if the Intex Krystal Clear SX925 Water Pump filter motor fails to start?
First, ensure the line cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. If the GFCI/RCD circuit breaker is tripped, reset it. If it trips repeatedly, turn off the breaker and consult an electrician. Also, the motor may be too hot; allow it to cool down before restarting.
How to fix a leaking air jet valve on an Intex Krystal Clear SX925?
If the Intex Water Pump air jet valve is leaking, tighten the air jet valve and make sure it’s facing up. If that doesn't work, turn the pump ON and run for a few seconds, then turn OFF, repeat 3 times. If the internal seal is dirty, remove the air jet valve, flush dirt out with water, and replace the valve back.
What to do if the timer on my Intex Krystal Clear SX925 Water Pump is inaccurate or can't be set?
If the Intex Water Pump timer is inaccurate or can't be set, turn off the pump and restart it 5 minutes later. Also, try re-setting the timer.
Why is there a small leak from the air jet valve when my Intex Water Pump is on?
If you have a small leak from the air jet valve when the Intex Water Pump is on, remove all accessories (such as solar mat, auto pool cleaner, LED light) from the water circulation line and place the air jet valve cap over the air jet valve. Do not cover the air jet valve with the valve cap under normal situations or when the pump is operating.
General| Brand | Intex |
|---|---|
| Model | Krystal Clear SX925 |
| Category | Water Pump |
| Language | English |
Details on selecting a suitable location and mounting the pump for optimal operation and cooling.
Step-by-step guide for assembling the sand filter tank, including inserting the center pipe and filter grid.
Instructions for properly filling the filter tank with sand, including precautions and distribution methods.
Detailed guide on correctly installing the 4-way valve assembly onto the filter tank, ensuring proper sealing.
Steps for connecting the pump motor to the tank base and filter hoses, including mounting considerations.
Explains the different settings of the 4-way valve and their corresponding water flow directions and functions.
Details the meaning of LED readings and the functions of the control panel buttons for operating the pump.
Guides users through the initial setup and startup process, including air release and backwashing the filter.
Instructions on how to set the operating timer or run the pump manually, including locking the keypad.
