Invacare XPO100 Service Manual (English)

Other manuals for Invacare XPO100

Service Manual20 pages

User Manual48 pages

Questions and Answers:

R
Ralph MaddenSep 4, 2025
What to do if Invacare Oxygen Equipment has continuous audible beep and red alarm indicator is illuminated. AND Flow indicators 1 & 5 are illuminated?
- T
  taylorcindySep 4, 2025
  If your Invacare oxygen concentrator is beeping continuously, the red alarm indicator is on, and flow indicators 1 & 5 are illuminated, it indicates a stuck button is being detected upon power up. Here’s how to address it: 1. Turn off the concentrator. 2. With the concentrator turned off, press each control button to check for a stuck button. 3. Turn on the concentrator, ensuring you are not holding the Power On/Off button once the lights begin to illuminate. If the alarm persists, switch to another source of oxygen and contact your equipment provider.
M
mroyAug 23, 2025
What to do if Invacare XPO100 has a continuous beep and red alarm at start up?
- L
  Lisa JohnsonAug 23, 2025
  If your XPO unit is beeping continuously with a red alarm indicator upon start-up, ensure that the cannula is correctly connected, not kinked, and properly positioned, and that you are breathing through your nose. If the alarm continues, switch to another source of oxygen and contact your equipment provider.
T
Timothy RobinsonSep 2, 2025
What to do if Invacare Oxygen Equipment has continuous audible beep and red alarm indicator is illuminated. Fan is On. AND Flow indicators 1 & 3 are illuminated?
- M
  Meghan BrownSep 2, 2025
  If your Invacare oxygen concentrator is beeping continuously with a red alarm, the fan is on, and flow indicators 1 & 3 are illuminated, it means the concentrator has become too hot or too cold during operation. To resolve this: 1. Allow the concentrator to cool down to less than 95ºF (35°C), or warm up to 50ºF (10°C), before turning the concentrator off, then on again. If the alarm continues, switch to another source of oxygen and contact your equipment provider.
V
victoria04Sep 1, 2025
What to do if Invacare Oxygen Equipment has continuous audible beep and red alarm indicator is illuminated. AND Flow indicators 1 & 4 are illuminated?
- L
  lisarobertsSep 1, 2025
  If your Invacare oxygen concentrator has a continuous audible beep, a red alarm, and flow indicators 1 & 4 are lit, it indicates the internal battery has become too hot or too cold during operation. Try the following: 1. Unplug any connected chargers. 2. Allow the concentrator to cool down to below 95ºF (35°C) or warm up to 50ºF (10°C) before resuming charging, or turning the concentrator off and then on again. If the alarm persists, switch to another oxygen source and contact your equipment provider.
J
Jason WardAug 31, 2025
What to do if Invacare Oxygen Equipment XPO concentrator does not operate when On/Off button pressed?
- J
  Jennifer BrownAug 31, 2025
  If your Invacare XPO concentrator isn't turning on when you press the On/Off button, here's what to check: * If it is a new device, connect the XPO concentrator to the AC power adapter, as the internal battery may be in shutdown mode upon arrival. * Ensure you're holding the On/Off button long enough (typically 2-3 seconds) until the front panel lights illuminate. * Connect the concentrator to either the AC or DC power adapter if the internal battery is discharged, and retry turning it on. If none of these steps work, switch to an alternate oxygen supply and contact your equipment provider, as there may be a malfunction.
L
lynnbridgesAug 29, 2025
What to do if Invacare Oxygen Equipment shows continuous beep, red alarm, and flow indicators 3, 4 & 5?
- J
  Jessica WilsonAug 29, 2025
  If your XPO unit is beeping continuously, the red alarm is illuminated, and flow indicators 3, 4, and 5 are lit, abnormal system operation has been detected. Turn off the unit, then turn it back on. If the alarm continues, switch to another source of oxygen and contact your equipment provider.
S
Sharon AllenAug 28, 2025
What to do if Invacare XPO100 Oxygen Equipment shows continuous beep, red alarm, and flow indicators 4 & 5?
- N
  Nathaniel RobinsonAug 28, 2025
  If your XPO unit is beeping continuously, the red alarm is illuminated, and flow indicators 4 & 5 are lit, abnormal compressor operation has been detected. Turn off the unit, then turn it back on. If the alarm continues, switch to another source of oxygen and contact your equipment provider.
P
Paul ValdezAug 27, 2025
What to do if Invacare XPO100 Oxygen Equipment shows continuous beep, red alarm, and flow indicators 3 & 4?
- V
  Victor ParkerAug 27, 2025
  If your XPO unit is beeping continuously, the red alarm is illuminated, and flow indicators 3 & 4 are lit, abnormal operation has been detected. Turn off the unit, then turn it back on. If the alarm continues, switch to another source of oxygen and contact your equipment provider.
J
Jennifer StarkAug 26, 2025
What to do if Invacare XPO100 shows continuous beep, red alarm, and flow indicators 1 & 5?
- A
  allenjohnAug 26, 2025
  If your XPO unit is beeping continuously, the red alarm is illuminated, and flow indicators 1 & 5 are lit, a stuck button is being detected upon power up. Turn off the unit. With the unit turned off, press each control button to check for a stuck button. Turn on the unit, ensuring you do not continue to hold the Power On/Off button once the lights begin to illuminate. If the alarm continues, change to another source of oxygen and contact your equipment provider.
S
sharon09Aug 25, 2025
What to do if Invacare XPO100 Oxygen Equipment shows continuous beep, red alarm, and flow indicators 1 & 4?
- J
  James PetersonAug 26, 2025
  If your XPO unit is beeping continuously, the red alarm is on, and flow indicators 1 & 4 are lit, the internal battery has become too hot or too cold during operation. Unplug the chargers if they are connected. Allow the unit to cool to below 95ºF or warm to above 50ºF before resuming charging or turning the unit off and then on again. If the alarm persists, use an alternative oxygen source and contact your equipment provider.