To Next PageTo Next PageWhy is my Invacare XPO100 Oxygen Equipment battery gauge dark when charging?
If the battery gauge on your XPO unit is dark while charging, first, try another power outlet and check all connections to the charger and the unit to ensure they are secure. The internal battery may also be outside the allowed temperature range for charging. Allow the unit to cool down to less than 95ºF, or warm up to 50ºF.
What to do if Invacare Oxygen Equipment is beeping intermittently with a red alarm?
If your XPO unit is beeping intermittently and the red alarm indicator is lit, it means your breathing rate may be too high for the device. Immediately reduce your activity to slow your breath rate. If the alarm continues, switch to another oxygen source.
What to do if Invacare XPO100 Oxygen Equipment shows continuous beep, red alarm, and flow indicators 1 & 4?
If your XPO unit is beeping continuously, the red alarm is on, and flow indicators 1 & 4 are lit, the internal battery has become too hot or too cold during operation. Unplug the chargers if they are connected. Allow the unit to cool to below 95ºF or warm to above 50ºF before resuming charging or turning the unit off and then on again. If the alarm persists, use an alternative oxygen source and contact your equipment provider.
What to do if Invacare XPO100 shows continuous beep, red alarm, and flow indicators 1 & 5?
If your XPO unit is beeping continuously, the red alarm is illuminated, and flow indicators 1 & 5 are lit, a stuck button is being detected upon power up. Turn off the unit. With the unit turned off, press each control button to check for a stuck button. Turn on the unit, ensuring you do not continue to hold the Power On/Off button once the lights begin to illuminate. If the alarm continues, change to another source of oxygen and contact your equipment provider.
What to do if Invacare XPO100 Oxygen Equipment shows continuous beep, red alarm, and flow indicators 3 & 4?
If your XPO unit is beeping continuously, the red alarm is illuminated, and flow indicators 3 & 4 are lit, abnormal operation has been detected. Turn off the unit, then turn it back on. If the alarm continues, switch to another source of oxygen and contact your equipment provider.
What to do if Invacare XPO100 Oxygen Equipment XPO does not operate when On/Off button pressed?
If your XPO unit doesn't turn on when you press the On/Off button, make sure you hold the button down until the front panel lights illuminate, typically for 2-3 seconds. If that doesn't work, connect the XPO to an AC or DC charger, as the internal battery might be discharged. If the problem persists, switch to an alternate oxygen supply and contact your equipment provider.
What to do if Invacare Oxygen Equipment has single audible beep and green 25% battery indicator is rapidly blinking?
If your Invacare XPO concentrator emits a single audible beep and the green 25% battery indicator is rapidly blinking, it indicates that the internal battery requires charging. To fix this: 1. Connect the XPO concentrator to its AC or DC power adapter, or to its supplemental battery pack. 2. If no other power source is available, switch to a reserve oxygen supply.
What to do if Invacare Oxygen Equipment has triple audible beep and green 25% battery indicator is blinking very rapidly?
If your Invacare XPO concentrator emits a triple audible beep and the green 25% battery indicator is blinking very rapidly, it means the internal battery is completely discharged and needs to be recharged. Here’s what to do: 1. Connect the XPO concentrator to its AC or DC power adapter, or to its supplemental battery pack. 2. If no other power source is available, switch to a reserve oxygen supply.
What to do if Invacare Oxygen Equipment has continuous audible beep and red alarm indicator is illuminated. AND Flow indicators 1 & 5 are illuminated?
If your Invacare oxygen concentrator is beeping continuously, the red alarm indicator is on, and flow indicators 1 & 5 are illuminated, it indicates a stuck button is being detected upon power up. Here’s how to address it: 1. Turn off the concentrator. 2. With the concentrator turned off, press each control button to check for a stuck button. 3. Turn on the concentrator, ensuring you are not holding the Power On/Off button once the lights begin to illuminate. If the alarm persists, switch to another source of oxygen and contact your equipment provider.
What to do if Invacare Oxygen Equipment has continuous audible beep and red alarm indicator is illuminated. Fan is On. AND Flow indicators 1 & 3 are illuminated?
If your Invacare oxygen concentrator is beeping continuously with a red alarm, the fan is on, and flow indicators 1 & 3 are illuminated, it means the concentrator has become too hot or too cold during operation. To resolve this: 1. Allow the concentrator to cool down to less than 95ºF (35°C), or warm up to 50ºF (10°C), before turning the concentrator off, then on again. If the alarm continues, switch to another source of oxygen and contact your equipment provider.
General| Brand | Invacare |
|---|---|
| Model | XPO100 |
| Category | Oxygen Equipment |
| Language | English |
