English
Invision MX450
Ergonomic Gas Assisted
Monitor Arm
Instruction Manual
VESA Compliance 75x75mm & 100x100mm
Recommended Screen Sizes 22” - 35”
Integrated Cable Management
Load Capacity 3 - 12kg (6.6 - 26.5lbs)
To receive large format PDF instructions please
email help@InvisionTechnology.co.uk
Parts List:
120mm threaded
bolt
Tools List:
Important:
1. Check the box contains all the items in the Parts List.
2. Check the screens VESA mounting measurements and
monitor weight.
3. Please read the instructions fully and plan how to mount
your monitor.
4. You may need additional tools: A drill will only be needed
if you are bolting it through a desk, the screwdriver is used
for removing the cable management.
www.InvisionTechnology.co.uk
WARNING!
Severe personal injury and property damage can result from improper installation or assembly. Please read the following warning carefully before beginning.
• If you do not understand the instructions or have any concerns or questions please contact us or a competent installer.
• Do not install or assemble if the product or hardware is damaged or missing. If you require replacement parts, please contact us at Invision for assistance.
• This product fits most VESA compliant 22”-35” LCD/monitors to a maximum weight of 12kg (26.5lb).
• For safe installation, the desk you are mounting it to must support minimum 3 times the weight of the total load (the mount, the monitor and all accessories weight).
• Do not use this product for other than the original design purpose.
• This product contains moving parts, please use with caution.
• When installing monitor take care not to damage electrical wiring or power source.
• Important - mains and data cables must be free from twisting and/or shearing.
• The manufacturer disclaims any liability for the modifications, improper installation or installation over the specified weight range. The manufacturer will not be liable for any damages arising from the use of, or
inability to use the product.
• This product is designed for indoor use only, use of this product outdoors could lead to product failure and severe personal injury.
• This product contains a high pressure gas piston This mechanism is not user serviceable and any interference could result in injury or damage. Please dispose of with caution
• In order to ensure the performance of the gas piston it is recommended to fully extend the arm several times per month.
Lets Get Started!
If you require assistance please contact us at: help@InvisionTechnology.co.uk
V202202211
1a - Clamp Base Installation
1. Remove the 2x screws from the monitor arm base (3) with 4mm Allen key (E) and remove the plastic
cable holder - see Diagram ‘A’.
2. Remove the screws from the rear of the clamp plate (5) with 5mm Allen key and put to one side - see
Diagram ‘B’.
3. Add the clamp plate (5) to the monitor arm base (3) replacing the 2x screws from step 1 and using 2x
M6 bolts (C) and 4mm Allen key - see Diagram ‘C’.
E (4mm)
Clamp
plate
Letters and numbers in ( ) are referred to in the Parts List
Diagram ‘A’
E (5mm)
Clamp
section
Diagram ‘B’
Diagram ‘C’
E (4mm)
4. To set the clamp to the correct height for your desktop/work-surface add the monitor base assembly to the
edge of your desk (use the front of your desk for now if it makes it easier) - see Diagram ‘D’. Take the clamp
section and wind out the knob fully. Position the clamp section (as in Diagram ‘B’) to the clamp plate and align
the holes. Once happy replace bolts from step ‘2’ with 5mm Allen key and tighten.
5. Add monitor base assembly to rear of desk and wind knob and fully tighten to the desktop/work-surface
- see Diagram ‘E’.
Please note: If you are mounting heavy screens on this monitor arm please evaluate what
desktop/work-surface you are mounting it to. (Example: Wooden surfaces like chipboard or MDF are
compressed high density boards and are less likely to cause marks or indentations. Natural wooden
surfaces are softer (not compressed) so you may consider adding protection.
Diagram ‘D’
E (5mm)
10 - 85 mm
Diagram ‘E’
2
To Next Page
Need help?
General
