IPC Gansow CT70 ECS User Manual

PLDC01911
CT70 ECS/CT40 BT60 ECS quick guide
This Guide is intended for quick consultation only and does not replace the Use and Maintenance Manual.
Before using the machine, read the Use and Maintenance Manual contained in the machine packaging thoroughly and rigorously respect all the
instructions.
PREPARATION/
OPERATION
1. Fill the detergent tank.
2. Release the emergency
button to turn the machine on.
3. Lower the squeegee using
the lever.
4. Press the brush button. The
machine automatically lowers
and attaches the brushes and
starts the suction motor.
5. Hold the brush button down for
3 seconds to choose the type of
operation, "MICRO SCRUB" or
with traditional brush.
6. Press the suction motor
button to disable suction if
you want to prewash the
surface.
7. Choose the direction of
movement by moving the
direction selector, turn the
potentiometer to set the
work speed.
8. Operate the drive lever.
9. Press the "H2O" button for
at least 2 seconds to
enable detergent flow.
Press the button repeatedly
to vary the quantity
delivered.
10. Adjust head pressure on
the surface to be cleaned
by pressing the button
repeatedly to vary the
pressure. The pressure
exerted is indicated by an
LED display on the control
panel.
11. Begin working.
12. When you have finished
cleaning, proceed as
follows:
• Turn the brush motor
off.
• Stop the detergent flow
• Turn the suction motor
off.
• Press the emergency
button.
• Raise the squeegee.
• If necessary, charge the
batteries.
DAILY
MAINTENANCE
Empty the dirty water drum
through the drain hose.
Clean the dirty water
drum.
Check the suction filter is
undamaged and clean.

IPC Gansow CT70 ECS Specifications

General

Brand	IPC Gansow
Model	CT70 ECS
Category	Scrubber
Language	English

Summary

Preparation and Operation Guide

Fill Detergent Tank

Add detergent to the machine's tank before operation.

Power On Machine

Release the emergency stop button to activate the machine.

Lower Squeegee

Lower the squeegee assembly using the designated lever.

Attach Brushes & Start Suction

Press button to attach brushes and activate suction motor.

Select Brush Operation Mode

Hold brush button to select 'MICRO SCRUB' or traditional brush mode.

Disable Suction (Prewash)

Press suction button to disable for prewash function.

Set Direction and Speed

Use selector for direction and potentiometer for work speed.

Operate Drive Lever

Use the drive lever to control the machine's movement.

Control Detergent Flow

Press 'H2O' button to enable/vary detergent flow.

Adjust Head Pressure

Adjust cleaning head pressure via button, indicated by LED display.

Begin Cleaning

Start the cleaning process after all preparations are complete.

Shutdown Procedure

Turn off motors, stop detergent, press emergency button, raise squeegee, and charge batteries.

Daily Maintenance Checks

Empty Dirty Water Drum

Drain the dirty water tank using the provided hose.

Clean Dirty Water Drum

Ensure the dirty water tank is thoroughly cleaned.

Check Suction Filter

Inspect the suction filter for damage and cleanliness.

Check Detergent Fill Filter

Inspect the detergent tank's fill filter for damage and cleanliness.

Clean Brushes & Microfibre

Wash the machine's brushes and microfibre cloths.

Check Battery Charge

Verify the current charge level of the machine's batteries.

Check Detergent Output Filter

Inspect the detergent output filter for damage and cleanliness.

Check Squeegee and Blades

Ensure the squeegee is clean and its blades are not damaged.

Charge Battery

Connect the charger to the machine's connector to recharge batteries.

Replacing Squeegee Blades

Blade Removal and Replacement

Guide on releasing clips, removing retainers, extracting, and replacing worn blades.

Automatic Brush Attachment

Attaching Brushes

Instructions for aligning and automatically attaching brushes to the head.

Releasing Brushes

Procedure to automatically release brushes by holding a button.

Troubleshooting Common Issues

Machine Not Starting

Check emergency button, battery charge, and water drum status.

Suction Motor Not Working

Verify suction hose, filter, detergent tank lid, and squeegee connections.

Machine Leaves Floor Wet

Check squeegee blades, debris, and suction hose for obstructions.

Machine Leaves Floor Dirty

Assess brush/pad suitability and if the floor was pre-brushed.

Machine Leaves Stripes of Wet Floor

Inspect squeegee blades for debris and verify correct adjustment.